Review Article

Selective Capture of CO2 from Mixture of Different Gases using Cellulose Acetate, Polyimide, Polysulfone and some other Polymers based Mixed Matrix Membranes: A Review

Asma Rashid Tariq1,2*, Saadia R. Tariq2, Tariq Mahmud1 and Misbah Sultan1*

1Institute of Chemistry, University of the Punjab, P.O. Box 54590, Lahore, Pakistan; 2Department of Chemistry, Lahore College for Women University, Lahore, Pakistan.

Received | August 08, 2020; Accepted | November 24, 2020; Published | December 11, 2020

*Correspondence | Asma Rashid Tariq and Misbah Sultan, Institute of Chemistry, University of the Punjab, P.O. Box 54590, Lahore, Pakistan; Email: asmartariq.9@gmail.com, misbahsultan@ymail.com

Citation | Tariq, A.R., Tariq, S.R., Mahmud, T. and Sultan, M., 2020. Selective capture of CO2 from mixture of different gases using cellulose acetate, polyimide, polysulfone and some other polymers based mixed matrix membranes: A review. Journal of Innovative Sciences, 6(2): 157-188.

DOI | http://dx.doi.org/10.17582/journal.jis/2020/6.2.157.188

Keywords | Gas separation, Polymer membranes, Mixed-matrix membranes, Fillers, Selective separation of CO2

1. Introduction

Membrane based gas separation technology feature cost effectiveness, simplicity, no phase conversion, energy efficiency, small foot prints and high mechanical stability (Muhammad et al., 2015; Marti et al., 2018; Rezakazemi et al., 2018) and hence gaining significant attention now a day (Hafeez et al., 2015). A great attention is being paid on development of potential carbon capture technologies so that increasing emission of CO2 can be controlled (Rehman et al., 2020). The separation of methane and carbon dioxide is an important problem in different fields. Also the recovery of methane from biogas is used as potential alternative to energy sources such as electricity generation, automobile fuel, and grid injection (Baker, 2002; Marian et al., 2007; Millar and Millar, 2003).

Inorganic membranes like Carbon Molecular Sieve Membranes (CMSMs) involve high cost due to their brittle nature so they are far more challenging (Caro et al., 2000; He et al., 2018). That is why polymeric materials are commonly used for CO2/N2 and CO2/CH4 separations (Adatoz et al., 2015). Both glassy as well as rubbery polymers have been used for membrane preparation. The glassy polymers demonstrate higher perm-selectivity and higher chemical resistance as compared to rubbery polymers (Chen et al., 2015). Furthermore, among the glassy polymers, polyimides demonstrate better performance in the CO2/CH4 separation.

The rapid growth in the field of polymer membranes has occurred after sighting the high flux asymmetric phase-inverted membranes in 1962. The successful trials of such membranes for gas separation encouraged for further testing and it was observed that these membranes appropriately separated helium gas from the natural gas (Gantzel and Merten, 1970). Later it was found that MMMs are associated with the superior separation performances as compared to that of the pure polymer membranes (Kulprathipanja et al., 1988).

The use of MMMs is promising alternative for extensive use of thermally rearranged polymers (Hu et al., 2020) and facilitated transport membranes (Wolińska et al., 2017), as well as blending of polymer membranes (Yong and Zhang, 2020) and cross-linking (Wang et al., 2020) etc. Despite all these advantages fabrication of a defect free MMM is still a hard challenge. However, such problems can be avoided by wise selection of polymer-filler pair and thus the performance of MMMs can be improved (Chung et al., 2007).

The use of filler particles of different shapes and sizes can help in this regard (Anjum et al., 2015a). Variation in the weight loadings of the filler particles as well as modification of filler particles surfaces (Venna et al., 2015) and use of different porous organic and inorganic fillers can improve the efficiency of MMMs modules towards gas separation (Goh et al., 2011; Song et al., 2012; Li et al., 2013).

The immensely explored materials for the fabrication of MMMs include porous and non-porous fillers for example activated carbons (He et al., 2018), carbon nano tubes (CNTs) (He et al., 2018), carbon molecular sieves (CMSs) (Ward and Koros, 2011), silica (Ariazadeh et al., 2020), Zeolites (Castruita-de León et al., 2020), TiO2 nanoparticles and MOFs (Li et al., 2017; Tariq et al., 2020).

A large number of polymers have been used for fabrication of MMMs using the above fillers and a large number of other fillers while all of the polymers and fillers pairs cannot be summarized in a single review. Examples of polymers that have been used for fabrication of MMMs include Polymer of intrinsic microporosity (PIM), cellulose acetate (CA), polyimide (PI), polysulfone (PSf), Polydimethylsuloxane (PDMS), Polybenzimidazole (PBI), polyethersulfone (PES), poly (ether ether ketones) (PEEK), sulfonated poly (ether ether ketone) (SPEEK), polyurethane (PUR) etc.

A detailed description of Cellulose acetate (CA), Polyimide (PI), Polysulfone (PSf) and some other polymers based MMMs with regard to gas separation studies is presented below:

1.1 Cellulose acetate

Cellulose is a perfect natural, renewable, biodegradable and biocompatible polymer (Zhang et al., 2017) that has been exploited for preparation of self-standing and supported membranes that are cost effective and exhibit the characteristics of virtuous compatibility, good toughness, and good fouling resistance, ease of process-ability, stability and high CO2 solubility (Moghadassi et al., 2014; Sanaeepur et al., 2014). It has been commercially used for gas separation specifically the separation of methane from CO2 (Muhammad et al., 2015).

The first CA based membrane systems were introduced in the mid of 1980 by Cyanara which was meant for separation of carbon dioxide from the natural gas (Baker, 2002). The CA membranes usually exhibit relatively low permeability towards CO2 and low CO2/CH4 and CO2/N2 gas pair selectivity (Mubashir et al., 2018a). The asymmetric hollow fiber membranes offer good permeability and selectivity and hence they have progressively gained importance in the gas separation processes (Tai-Shung et al., 1994).

1.1.1 Hollow fiber CA- MMMs

Among numerous configurations, hollow fiber membranes (HFMs) offer the benefits of high packing density, low pressure drops, high pressure stability, and easy scale up (Pang et al., 2018; Wahab et al., 2012). They show good industrial performances for gas separation but the limitations of instability at elevated temperatures and pressures are also associated with these membranes. Incorporation of filler such as CNTs (Widjojo et al., 2008), zeolites (Li et al., 2006a) Montmorrillonite (Zahri et al., 2016) and polysilsesquioxanes POSS (Zhang et al., 2016a) are known to improve the structural properties and thermal stability of resulting HFMMMs (Zhang et al., 2016a). But these fillers may suffer from the problem of incompatibility with polymer matrix as well as the defective membrane may be formed (Gao et al., 2018). The defects can efficiently be avoided by using several suitable post-treatment methodologies such as polydimethylsiloxane (PDMS) coating, thermal treatment, and sometimes PDMS coating combined with thermal treatment (Zulhairun et al., 2015). MOFs (Tsai et al., 2018) have proven as prospective fillers which are inherently light weight. These replace the conventional fillers due to their unique properties. Therefore, extensive study on CO2 adsorption has been carried out using several famous MOFs including the examples of UiOs, ZIFs and MILs (Kim et al., 2016a).

The filler and the polymer chosen highly affect the permeation properties of HFMMMs (Cheng et al., 2013). Commonly, HFMMMs are frequently fabricated using CA, cellulose triacetate, polysulfone (PSf) and polyimides. However, CA effectively removes CO2 from mixture of CO2 and CH4 even when the humidity is present there (Saneepur et al., 2014). Mubashir et al. (2019) published feasibility of application of combined use of thermal treatment and PDMS coating methodologies on NH2-MIL-53(Al)/CA HFMMMs for significant improvement in their performance relating to the separation of CO2 either from CH4 (CO2/CH4 gas pairs) or from N2 (CO2/N2 gas pairs). Thermal treatment of pristine CA-HFM and NH2-MIL-53(Al)/CA HFMMM at 170°C resulted in improved selectivities of HFMMM for the CO2/N2 and CO2/CH4 gas pair from 7.7 to 8.4 and 9.1 to 9.9 respectively in comparison with untreated HFMMMs and neat CA membranes. Adhesion of the MOF with the CA polymer matrix reduced the CA chain mobility which resulted in an increased Tg value of 220 ºC than the pristine CA-HFM (Mubashir et al., 2018b).

The gas permeance exhibited a decreasing trend for CO2 > N2> CH4 as compared to that for CA-HFM that was accounted for the differences in the solubility of the two gases (Sanaeepur et al., 2014). A decrease in permeability of CO2 and separation factors for CO2/N2 and CO2/CH4 mixed gas pairs were attributed to the polarization effect and competition between the two gases which subsequently resulted in the reduced CO2 adsorption−diffusion rates through this HFMMM. While CO2 swelling effect trimmed down the CO2 solubility coefficient and hence CO2 permeance was observed to be decreased. An enhanced CO2 pressure was also associated with its enhanced diffusion (Balçik and Ahunbay, 2018).

Asymmetric CA HFMs prepared by applying a dry/wet spinning procedure with non-solvent induced phase separation (NIPS) executed superior selectivity. In case of permeate; the CA HFM module exhibited a maximum of about 5% higher CO2 concentration than the existing PSf membrane module at the same stage.

A smaller recyclable stage-cut condition was also observed for CA HFM module in contrast to the existing Polysulfone membrane module. Slightly increased recovery efficiencies were obtained for CH4 in comparison with the existing Polysulfone membrane module at similar stage-cuts (Jeon and Shin, 2017).

1.1.2 Flat sheet CA-MMMs

The solvent system plays an important role in fabricating defect free membrane with non-selective voids (Mubashir et al., 2018a). Mubashir et al. (2018a) used N-Methyl-2-pyrrolidone (NMP) as a solvent to fabricate CA membrane with improved fractional free volume and hence they executed improved gas permeance (Mubashir et al., 2018a) as compared to those prepared in THF and acetone (Moghadassi et al., 2014; Achoundong et al., 2013). The membrane showed the ideal selectivity values of 10.71 and 8.80 respectively for CO2/CH4 and CO2/N2 gas pairs and the CO2 permeability to be 15.56 Barrer. The solubility differences of gases in the CA matrix caused a decreasing gas permeability in the order CO2 > N2 > CH4 (Moghadassi et al., 2014). NMP enhanced the hydrogen bonding between OH− and C-OH of neighboring rings that increased the rigidity of the CA chain which rendered improved gas permeation efficiency. Thus, NMP was recommended as an effective solvent for fabrication of other types of membranes as well (Mubashir et al., 2018a).

Mubashir et al. (2018b) investigated the fabrication of new flat sheet MMMs by the incorporation of NH2–MIL53–Al MOF as an additive into the CA polymer for getting better separation performances. The Brunauer Emmett and Teller (BET) surface area and micro pore volume of the prepared membranes were found to be 637 m2/g and 0.28 cm3/g, respectively (Kim et al., 2012a). The agglomeration of MOF particles in CA based MMMs was observed upon increased filler loadings with an increase in glass transition temperature (Tg) of the obtained MMMs (Mubashir et al., 2018b).

The improved CO2 permeability besides the CO2/N2 and CO2/CH4 ideal selectivities was observed upon incorporation of the aminated MOF into the CA matrix. A 200% increase (30 bar) in the CO2 plasticization resistance was also observed as compared to the neat CA membrane. Thus, the fabricated MMMs were found to be the potential candidates for abstraction of CO2 from the natural gas and flue gas at industrial scale (Mubashir et al., 2018b).

Two-dimensional MOF based nano-sheets possessing molecular sieving properties are exceedingly preferred as polymer additives for application in the separation of gases. But it is necessary to impose adhesion between the polymer matrix and that of the MOF module and to overcome the MOF particles agglomeration (Zhang et al., 2018).

The MOF membranes suffer from poor mechanical stability, defect formation during MOF membrane formation and a lack of interface interactions (Adatoz et al., 2015) that lead to compromised selectivity performance of the membranes due to the weaker interactions between the test polymer and the MOF particles (Zhang et al., 2016b). Furthermore, almost all MOFs cannot be dispersed well in aqueous system so organic solvents are usually used for synthesizing MOF/polymer composite membranes (Zhang et al., 2018).

Zhang et al successfully fabricated a carboxymethyl cellulose (CMC) cross-linked ZIF-L membrane by using an organic solvent free method. Here, CMC was used as the gas barrier and adhesive matrix through a facile, organic-solvent-free method. The dispersion stability of ZIF-L nanosheets was high in an aqueous system by successful combination of carboxymethyl cellulose and 2D zeolitic imidazolate framework ZIF-L nanosheets due to the interactions between CMC and ZIF-L nanosheets and the anion charge repulsion effect between the complex particles (Zhang et al., 2018).

These improved selectivities for mixed gas were achieved due to the gas barrier offered by the CMC matrix phase and sieving property of ZIF-L. The membranes loaded with 30-wt % ZIF-L nanosheets showed the highest separation ability. Moreover, CMC acted as a capping agent via simple synthesis technique and performed well as an adhesive matrix to fabricate a MOF-based membrane that could possibly be extended to various systems (Zhang et al., 2018).

Recently Kim et al. (2019) prepared the Zeolitic imidazolate framework-302 (ZIF-302) using 5(6)-methylbenzimidazole (mbImH) 2-methylimidazole (2-mImH) and embedded into the CA matrix using phase inversion technique. Similarly, Hou et al. (2017) fabricated HKUST-1 MOF based MMMs by selecting HKUST-1 MOF as additive and CA as the continuous matrix. The CA membrane was crack free while the fibers were twisted in the CA matrix. Further the particle size of HKUST-1 was in the range of 15-20 µm and 60 wt. % loading of HKUST-1 was used to fabricate the MMMs that yielded sufficiently high BET surface area of 459 m2 g-1. However, both of these MMMs were not used for the gas separation tests (Hou et al., 2017).

A variety of layered nanoporous materials are in vogue, for instance layered silicates such as MCM-22, Nu-6 and UZAR-S1 (Roth et al., 2011; Gorgojo et al., 2012; Rubio et al., 2010), layered borogermanates (Xiong et al., 2007) and layered aluminophosphates (AlPOs) (Jeong et al., 2004) as well as 3D AMH-3 is another nano-porous layered silicate possessing pores without octa membered rings. Its crystallographic pore size is 3.4 Å that renders it potentially useful for significant separations of various gases for example CO2/CH4 and H2/N2 (Jeong et al., 2003).

Interest in nano-porous layered silicate/polymer composite or mixed matrix membranes is increasing day by day as the exfoliated selective layers or flakes present high aspect ratio (Kim et al., 2013). Thus the molecular sieving is enhanced which in turn creates an exceedingly high circuitous pathway for transportation of the slow moving molecules (Kim et al., 2013). Kim et al. (2013) performed membrane synthesis along with the detailed study of microstructural analysis, and evaluation of mixed gas permeation capacities and further established that the nanoporous flake/polymer based MMMs permit momentous improvement in the values of gas permeability while keeping the selectivity sustained. So, the exfoliated flakes of SAMH-3 were used to fabricate CA membranes by using THF as solvent (Kim et al., 2013). The layers of the used silicate possessed a high degree of exfoliation when present in the Cellulose Acetate module but merely 4–8 layers were found to compose the exfoliated flakes of thickness 15–30 nm. The resulting CA membrane module obtained after incorporation of SAMH-3 flakes in the range of 2–6 wt. % exhibited a significant increase in the CO2 separation efficiency for the CO2/CH4 gas pair (Kim et al., 2013). Moreover, the permeability values of CO2 were observed to be significantly increased while the selectivity remained sustained. The transport phenomenon of such kind is governed by the competing effects of transport over the pores of layered SAMH-3 in addition to the interlayer spaces and is found potentially operative via the CA matrix of relatively lower-density. So the conventional models were unable to explain this transport (Kim et al., 2013).

Figure 1 combines that the transport mechanism of CO2 and CH4 molecules, while the actual illustration describing the transport pathways of these gases can be found elsewhere (Kim et al., 2013). Transportation of CO2 is sieving through the layers of membranes. This also involves the CH4 molecules exhibiting tortuous diffusion while Kundsen transport was observed for both the gases through inter layer species as illustrated in Figure 2.

 

 

CAU-1-NH2 is well known for its microporosity, good stability and well established three-dimensional geometry. The octameric bricks consisting of Al in its constitution as (Al8(OH)4 (OCH3)8)12+ units are found to be arranged in the body-centered cubic as connected via twelve aminated terephthalate ligand connectors (Yin et al., 2014; Si et al., 2011). The resulting MOF possess highly rigid framework with exceptional thermal stability values up to 573 K (Yin et al., 2014; Ahnfeldt et al., 2009). It was in 2016 when Jian et al. (2017) reported the use of CAU-1-NH2 MOF in its thin and tubular configuration to fabricate CA matrix. The obtained MMMs were tested against CO2 and Nitrogen gas mixture constituting equal composition of both gases. A high separation factor of 14.8 was obtained for CO2/N2 gas pair for the resulting MMM in addition to the high permeance. Yeong and Khoo have demonstrated that the filler loadings greater than 5 wt. % lead to sedimentation as well as agglomeration that in turn increased the CO2 permeability (149%) besides the increase in CO2/N2 selectivity (81%) in comparison to the pure cellulose acetate membrane module (Yeong and Khoo, 2019).

 

 

PDMS possess siloxane linkages which render it highly permeable for gas with a compromised selectivity (Pratibha and Chauhan, 2001). Although its mechanical strength is insufficient for industrial scale applications (Jeon and Shin, 2017) however the CA membranes coated with PDMS experience reduced defect flow to show appropriate permeability values in addition to the improved selectivity of gases (Jeon and Shin, 2017).

Zeolite-filled MMMs feature the potential to realize improved separation performances with nearly equal or comparatively greater fluxes in comparison with the prevailing polymer membranes sustaining their benefits (Li et al., 2013b; Liu et al., 2008). But non-selective “voids” created as a result of insufficient or weak interactions or prevalence of de-wetting phenomena in the polymer chains in addition to the impact of external zeolite surface can lead to a decrement in the performances of the obtained MMMs (Dong et al., 2013).

Different approaches may be followed to bring improvement in the polymer-zeolite adhesion in resulting zeolite-filled MMMs for improved gas separation. Such strategies include chemical treatment of the filler surface by introducing different organic functional groups; (Bae et al., 2009) creation of a roughened or nanoscopic non-organic whisker-like structure (Lydon et al., 2012; Shu et al., 2007; Kim et al., 2012b); surface initiated polymerization with preformed zeolites, (Shu et al., 2007); the in situ formation of zeolite particles inside the pre-fabricated polymer matrices; (Rezakazemi et al., 2014) annealing the membranes above the glass transition temperature of the polymer, (Rezakazemi et al., 2014) or addition of plasticizer and/or antiplasticizer additives into the membrane formulation (Şen et al., 2007).

Zeolite-filled porous MMMs harvest better permeation performance but couple with an unwanted reduction in selectivity in comparison with the dense MMMs (Funk and Lloyd, 2008; Chen et al., 2014). Sanaeepur et al. (2014) claimed the first time investigation of the proper modification of a homogeneous CA membrane using a micro-sized nanoporous zeolite employing the silylation reaction to attain good adhesion between the polymer and zeolite filler in the resulting MMMs. They used APDEMS to perform as the silane coupling agent and the precursor for zeolites synthesis was micro-sized nanoporous sodium zeolite-Y (Na-Y). The average diameter of the particles was increased as a consequence of Zeolite modification in addition to an increase in the overall volume and external surface area while the micropore surface areas concomitantly decreased. The modified zeolite particles exhibited improved crystallinity besides imparting improved morphological features to the obtained mixed matrix membranes in comparison with the CA/NaY MMMs. Additionally, the numbers and sizes of the unwanted agglomerates and cracks were considerably reduced. The MMMs fabricated with NaY-sm particles loading upto 20 wt. % exhibited the most favorable permselectivity behavior at pressure of 2 bar (Sanaeepur et al., 2014).

A schematic representation of membrane modification for enhanced CO2/N2 selectivity improvement via the facilitated CO2 transport in the CA/NaY-sm membranes can be found in reference Sanaeepur et al., 2014. The most widely used kinetic diameter was chosen here for the effective molecular diameters of the penetrant gases which are respectively 3.3 and 3.64 A for CO2 and N2 molecules (Sanaeepur et al., 2014).

The CA/NaY-sm MMMs executed relatively reduced CO2 permeability as compared to the CA/NaY MMMs. Moreover, the NaY-sm filled MMMs showed an average CO2/N2 selectivity of 6.34% in comparison to the MMMs filled with the unmodified NaY particles (≥ 4 bar). The characteristic crystalline peaks for both of the CA and zeolites were present in the membrane after incorporation of NaY or NaY-sm Zeolites but with a slight loss in number of crystallinity of CA after filler loading (Sanaeepur et al., 2014).

The particles were observed to be well distributed in unmodified NaY zeolite loaded membranes with a few agglomerates (Sanaeepur et al., 2014) at higher zeolite loadings (Sanaeepur et al., 2015; Amooghin et al., 2015). The gas molecules actually cannot access these points to move through and so these points are the dead zones in the membrane matrix. The surface modified zeolites appreciably improved the particle distribution. The modification of zeolite surface using APDEMS brings a high hydrophobicity in the resulting material as compared to the pristine zeolite. Further, the existence of some amount of moisture can be an additional factor for adsorption of CO2 (Sanaeepur et al., 2014).

An increase in pressure was found associated with a decreased CO2 permeability of all the membrane samples so the polymer chain densification reduces gas permeability.

Thermal annealing has proved to be an effective method for controlling the crack formation in CA based MMMs. Sanaeepur et al., 2014 fabricated dense CA based MMMs for separation of CO2 from Nitrogen by using micro-sized nano-porous sodium zeolite-Y (NaY zeolite) particles up to 25 wt. %. They efficiently controlled some undesirable cracks in the selected cross sectional area of the well dried pristine CA membranes by annealing. However, further growth of cracks was possibly a result of enhanced NaY zeolites loading from 5 to 25 wt. %. The resulting membranes showed a two-fold permeability increase of CO2 without compromising the CO2/N2 selectivity. Additionally, the CO2-induced conditioning/plasticization of the glassy CA was reduced and the plasticization pressure was substantially increased (Sanaeepur et al., 2015).

Bos et al. (1999) described that the intra-molecular hydrogen bonding present in the CA may be broken by providing sufficient thermal energy. Consequently, the polymer chains can achieve further mobility so as to establish inter-molecular hydrogen bonds between the polar (hydroxyl and acetyl) groups of different chains. These attractive interactions present within polymer chains cause efficient reduction in the free volume, which ultimately results in formation of more compact membranes. Thus, the membrane annealing reduces the permeability. The MMMs fabricated with different weight loadings of the filler ranging from 0 to 25 wt. % showed a small drop in the permeabilities of CO2 with gradual increase in pressure at least up to plasticization pressure (Sanaeepur et al., 2015). Beyond the plasticization pressure, the permeabilities of the same were observed to increase once again with the increase in pressure (Sanaeepur et al., 2015).

Achoundong et al. (2013) used GCV-modification technique so as to modify the CA films by grafting vinyltrimethoxysilane (VTMS) to –OH functional groups. The hydrolyzed methoxy groups present on the silane subsequently underwent condensation to create a polymer network. The modified MMMs showed comparable CO2/CH4 and H2S/CH4 selectivities than that of the pristine CA membrane; nevertheless, the pure H2S and CO2 permeabilities were 165 and 139 barrers respectively which were far higher than the neat polymer. The GCV modified MMMs executed lower Tg and lower crystallinity in adition to increased flexibility in comparison to the neat CA. The vinyl substituents delivered by VTMS imparted improved flexibility in the resulting MMMs accompanied with reduced brittleness which could help with the structure of an asymmetric membrane (Achoundong et al., 2013).

Najafi et al. (2018) used silica nanoparticles as fillers to study their effects on the permeance of pure gases such as N2, O2, and CO2 while employing CA as polymer matrix. The thermal phase inversion method was used to fabricate CA and CA/silica nanocomposite membranes. SEM micrographs revealed the silica nanoparticles to be well dispersed into the polymer matrix with unavoidable agglomeration of the silica nanoparticles. These nanoparticles were quite compatible with the polymer.

Gas permeation experiments for the prepared composite membranes showed an increased permeability of condensed CO2 gas with pressure increase. Nonetheless, increasing the silica loading up to 20 wt%. reduced the permeability of N2 gas at pressure changes from 0.18 to 0.09 barrer. The addition of silica particles into the polymer matrix not only improves the total number of the -OH- groups but also induces the morphological changes at the polymer-silica interface. The solubility of the gas molecules increases in lieu of these changes, with a consequent reduction in diffusivity of the gas molecules. Consequently, improved CO2/N2 selectivity was observed in the resulting nanocomposite membranes (Najafi et al., 2018).

Lower mechanical stiffness and the consequent higher brittleness of MOFs in comparison to the zeolites is accompanied by undesirable effects of gate opening, breathing, and linker dynamics (Caro, 2011; Ferrey and Serre, 2009; Li et al., 2009). Flexibility of the metal-organic backbone of MOFs makes their modulation as a self-assembled membrane to be easy; however, the flexible structure of MOFs prevents an appropriate separation based on the penetrant sizes (Caro, 2011) and leads to lower CO2/CH4 selectivity of MOF membranes as compared to the zeolites (Li et al., 2006b).

The disadvantages of zeolites/MOFs which are the two best adsorbents in the case of MMMs could be overcome by tailoring the idea of “ship-in-a-bottle” (SIB). The SIB approach was first used to fabricate the zeolite catalysts (Sanaeepur et al., 2019) by encapsulating the catalyst molecules in the zeolite (host) cavities. A guest molecule (like a ship) is formed by assembling its separate constituent species in the zeolite cavities and becomes larger than the pore aperture of the (bottle-like) zeolite. The guest nano-materials are confined and, can freely move around within nano-scale domains of the host cavities and, hence, prevent leaching (Kahlen et al., 1998; Herron, 1986).

Thus gas separation properties of MMMs could be enhanced by interior modification of an inorganic nano-porous particle. Sanaepur et al. (2019) used SIB, as a novel synthesis strategy to encapsulate a polyaza macrocyclic Ag-ligand complex into the zeolite Y, which resulted in a new host-guest nano-composite. It was consequently incorporated into CA to fabricate a novel MMM for CO2 separation. The results showed a promising increase in both the CO2 permeability (45.71%) and CO2/N2 selectivity (40.28%) of the prepared MMMs over its pristine CA membrane (Sanaeepur et al., 2019).

The CO2 separation using a membrane is not merely a procedure to physically sieve out CO2 via a wise control over pore size of the selected membrane. The separation procedure specifically for composite dense membranes is primarily governed by diffusion and solubility phenomena of the gases. The blended constituents of composite membranes usually possess high CO2 adsorption capability while, the adsorption kinetics of the gases directly influence their diffusion and the solubility. A complete understanding concerning the adsorption performance of CO2 was explored in terms of its diffusion and solubility using pristine and composite CA. The CA-TiO2 composite membranes were prepared using 20 wt. % of pure TiO2 (Hafeez et al., 2015).

TiO2 nanoparticles were homogenously dispersed in the blended membrane (Hafeez et al., 2015) but with appearance of some nanoscale granular morphology (Sijbesma et al., 2008). The hydrophilic TiO2 nanoparticles impart increased thermodynamic instability towards the membranes, during solvent–water exchange. Accordingly, increasing the amount of TiO2 nanoparticles within the polymer matrix could make the membrane porous. That is why optimized (20 wt. %) loading of TiO2 nanoparticles in the CA matrix did not prompted the solvent–water exchange process. Also the porosity was not imparted in the blended membranes. The adsorption of CO2 through both the pristine CA and blended membranes took place in a parallel fashion and this adsorption was increased with the pressure.

The blended CA membrane exhibited comparatively higher amount of CO2 adsorption in comparison with the pure CA membrane because of inability of CO2 gas to diffuse and its ease of solubilization in the dense pristine CA membranes. Furthermore, addition of TiO2 nanoparticles caused an increase in the free volume between the polymeric chains that might enhance diffusion as well as adsorption of CO2 in polymeric matrix. The –OH- functionality on TiO2 has its own role in increasing CO2 adsorption (Hafeez et al., 2015).

Abedini et al. (2011) proposed that the temperature can easily affect the polymer chains in the absence of inorganic particles in the membrane. They also prepared CA/TiO2 hybrid MMMs of different compositions by dispersing varying concentrations of inorganic filler in the casting solutions of CA. The addition of TiO2 nanoparticles imparted porosity in the obtained hybrid membranes because of resultant increase in the mean pore size. The facilitated formation of macro voids occurred in the membrane sub-layer upon increasing the amount of TiO2 nanoparticles in the cast module from 0 to maximum 25 wt. %. The addition of TiO2 nanopaticles increased the thermal stability of hybrid membranes (Abedini et al., 2011).

The MMMs offer the advantage to overcome the discrete deficiencies related to the inorganic particles as well as polymers in order to realize higher CO2 separation performances (Scholes et al., 2008). Nevertheless, the membranes suffer from insufficient interfacial compatibility between the polymer and the inorganic phase which ends up in the creation of unselective voids within the membranes (Mahajan and Koros, 2000). Ahmed et al described synthesis of thin dense skin layer and defect free MMMs from cellulose acetate (CA) with homogeneous distribution of MWCNTs by using the wet phase inversion method. The separation efficiency of the obtained MMM for CO2/N2 gas pair was studied at 0.1 wt. % loading of MWCNTs functionalized with β-CD (MWCN-F). MWCNTs-F were also found to be less agglomerated in CA matrix (Ahmed et al., 2014).

Troota et al. (2011) described that β-CD can entrap CO2 even at room temperature and atmospheric pressure. Neoh et al. (2006) made use of the β-CD cavity for encapsulation of CO2. Considering the above work it can be deduced that embedding of β-CD into the CA polymer matrix could be beneficial for CO2/N2 separation.

The Nano channels were created as beneficiary of the smooth walls of MWCNTs so that gases can fastly be transported (Sanip et al., 2010, 2011) while the treatment using β-CD does not end up with the destruction of tubes with small diameter (Ahmed et al., 2014). So the MMMs are expected to exhibit good separation efficiency.

There was a significant increase in the permeance of both the CO2 and N2 with the increase in loading of MWCNTs from 0.05 wt. % to 0.1 wt. % in the polymer matrix (Ahmed et al., 2014). It was the result of presence of high diffusivity MWCNTs tunnels within the polymer matrix having good interaction between the MWCNTs and polymer phase (Kim et al., 2006a). The selectivity was insignificantly changed with the increasing pressure (Ahmed et al., 2014) which provided indication of the additional mechanical strength provided to the MMM by the presence of MWCNTs-F (Sanip et al., 2011; Liu et al., 2007).

Considering the importance for the design of membrane gas separation system, a number of models had been developed with the simultaneous growth of MMMs, so that CO2 permeation performances could be estimated (Emovon et al., 2017). Maxwell model (Mubashir et al., 2016; Bouma et al., 1997), Lewis-Nielsen model (Lewis and Nielsen, 1970), Bruggeman model (Goncharenko, 2003) and Pal model (Pal, 2007) are considered as basic models to predict permeability of CO2 in the MMMs.

The estimation of CO2 permeability of MMMs using models is important for the design of membrane separation system. The modified Maxwell model applied for NH2-MIL-53(Al)/CA system, revealed the absolute average error (AARE %) of 1.66%, which was lower than the AARE% obtained from the other theoretical models (Mubashir et al., 2018c).

Increase in filler loading simultaneously increased the viscosity of the NH2-MIL-53(Al)/CA solution so as to create a stress between filler and polymer matrix (Ahmed et al., 2014). This stress might have developed the pseudo dispersed phase in the CA polymer which could have increased the interfacial defects (θi) in MMMs (Abedini et al., 2014; Emovon and Mgbemena, 2018; Adeeb et al., 2018).

1.2 Polyimide

Polyimides (PI) are high performance glassy polymers with outstanding heat and chemical resistance (Mathew et al., 2007) and high mechanical strength (Mathew et al., 2007) and thus offers better selectivity in a number of major pairs of gases (for example O2/N2 and CO2/CH4). These exceptional properties render the PIs a striking candidate among a number of polymeric membranes for gas separation studies. Since the production of marketable PIs membranes, several of those have been commercialized for the purpose of gas separation. Their commercialized uses have been reported in the separation processes by the industries such as Ube (Japan) and the DuPont (USA) (Liaw et al., 2012).

Imide functional group is the major unit constituting the PI backbone as can be seen in the Figure 3. Fully aromatic PIs possess linear structure and they are derivative of an aromatic dianhydride and a diamine. The semi aromatic PIs comprise any one of the aromatic monomer i.e. either of the constituting units that is dianhydride or a diamine are aromatic and the other monomeric unit may be the aliphatic one. Fully aliphatic PIs result from combination of aliphatic constituting monomers of diamine and dianhydride (Mathew et al., 2007). PIs have broad applications in photoresists, dielectric films, passivation (Mathew et al., 2007) and in synthesizing films and fibers, coatings molding powders and composites.

 

 

Raw multi wall carbon nanotubes (r-MWCNTs) with 0-6 wt. % were used to fabricate PI membranes which increased the separation factor for CO2/CH4 gas pair (from 19.05 to 45.75) and decreased the carbon dioxide (from 9.15 GPU to 5.49 GPU) and methane permeances. When the 2 wt. % r-MWCNTs were added into the spinning dope, the CO2/CH4 separation factor executed an increase from 46.61 to 72.20 that was comparable to the flat sheet MMMs. Sufficient segmental-level association existed between both of the phases comprising the MMMs which led to the formation of rigidification of polymer regions at the polymer/r–MWCNTs interfacial points and it was evident from increasing Tg values upon increased filler loadings (Aroon et al., 2010).

In another work, Sanip and co-workers (Sanip et al., 2011) reported enhanced functionality of multi-walled CNTs (MWCNTs) by use of beta-CD (β-CD). The 0.7 wt. % loading of functionalized MWCNTs into polyimide membrane led to the formation of uniform finger-like structures in the resulting MMMs so as to facilitate the faster gas diffusion through the polymer matrix

MCM-41 functionalized with -SO3H was used to fabricate Matrimid® 9725 based MMMs. The functionalized fillers possessed a good contact with the polymer phase and were homogenously dispersed throughout the continuous phase. The activation energies of permeation in the resulting MMMs were higheras the introduction of massive –SO3H groups resulted in the creation of pores with reduced diameter. The highly porous filler along with functionalized polar groups led to a concurrent increase in the solubility co-efficients and diffusion of CO2 as compared to the pristine membranes. Consequently, the functionalized MMMs showed upto 31% increase in CO2 permeability and 14% increase in CO2/CH4 selectivity (Khan et al., 2013a).

Ordered mesoporous silica such as COK-12 particles featuring remarkably ordered 2D hexagonal structure possess short but straight pores that allowed a faster diffusion of penetrant gas when used as additives in MMMs based on Matrimid. The increased gas permeabilities of the test gases (N2, CH4 and CO2) in comparison with pure Matrimid membrane resulted from the mesopores existing in the structure of additives. The addition of filler causes a decrease in activation energy of permeation. The mixed gas selectivity for both of the CO2/CH4 and CO2/N2 gas pairs was found to be lesser than the ideal gas selectivity for all of the tested MMMs; most probably the competitive sorption played its role (Khan et al., 2015).

Free volume causes a positive influence on gas permeability as well as selectivity. Increased sorption efficiency could be achieved for increased loading of carbon phase in the CSM@matrimid® 9725 MMMs. It was attributed to the increased affinity of the CO2 gas molecules besides increasing free volume within the continuous phase and creation of extra porosity. The results showed a 2-fold increase in CO2 mixed gas selectivity (up to 42.5) and a 6-fold increase in permeability for the CO2/N2 and CO2/CH4 gas mixtures which is a significant improvement (Anjum et al., 2015a).

Various factors influence the performance of polyimide membranes. Chaidou et al. (2012) prepared Matrimid® 5218 based MMMs by incorporating zeolite 13X, 4A and ZSM-5 by solution casting procedure. The results obtained after gas permeation trials indicated a significant rise in the permeability values of He, H2, N2 and CO2 with increase in zeolite loadings (Chaidou et al., 2012). Slightly improved selectivity was obtained for H2/N2 gas pair for small addition of ZSM-5 and zeolite 13X however a decreasing trend in selectivity was observed for zeolite 4A and for high wt. % loadings of the other two zeolites. Moreover, an exceptionally improved selectivity was observed for the CO2/N2 gas pair with the addition of all of the three zeolites in the PI membrane in contrast to the selectivity of H2/CO2 gas pair which remained too low (1–3). The obtained permeabilities were quite higher than the predicted values of selectivity by employing the Maxwell model. However, the predicted permeabilities of H2 and N2 for the PI-4A system were an exception as they were in consistency with the observed permeabilities. The proposed modification in the Maxwell model helped in predicting the permeabilities of PI-zeolite 4A MMMs, but unfortunately they were incapable to simulate the increase in permeability induced by interfacial voids in the PI-zeolite 13X and PI-ZSM-5 MMMs systems (Chaidou et al., 2012).

Zeolite-T/6FDA-durene MMMs exhibited 172% rise in ideal selectivity (19.1) for the CO2/CH4 and 80% increase in CO2 permeability (843.6 Barrer) with incorporation of only 1 wt. % zeolite-T loading in comparison with pure 6FDA-durene membrane. Furthermore, the MMMs showed a significant improvement in CO2 plasticization resistance (up to 20 bar) in contrast to unfilled 6FDA-durene membrane which could show the CO2 plasticiization resistance of only 5 bar (Jusoh et al., 2017a).

The MMMs comprising of 6FDA-based polyimide matrix fabricated with amine-functionalized T-type zeolite had enhanced polymer-zeolite adhesion in MMM compared with MMM loaded with unfunctionalized T-type zeolite which resulted in permeability value of 858 Barrer for CO2 and selectivity of CO2/CH4 gas pair to be 22.5 on the other hand. While, MMM incorporated with unfunctionalized T-type zeolite displayed permeability value of CO2 to be 844 Barrer and selectivity of CO2/CH4 gas pair to be 19.1 (Jusoh et al., 2018). Similarly, Nik et al. (2012) disclosed that the inclusion of amine-grafted MOF-199 in 6FDA-ODA matrix efficiently improved the dispersal of particle in the continuous phase and subsequently ended up with elevated values of permeability for CO2 and selectivity of the CO2/CH4 gas pair (Nik et al., 2012).

Aminosilane grafted zeolite T/ 6FDA-durene MMMs also showed improved selectivity for CO2/CH4 gas pair (Jusoh et al., 2017b) that was attributed to the capability of amino silane modified zeolite T to minimize the mobility of gases through the non-selective holes (Ismail et al., 2008). Whereas the selectivity of MMMs embedded with the unmodified zeolite T for the same gas pair was found to be 19.1. The Tg values also supported the better performance of the MMMs embedded with grafted fillers used in this study. The success of this modification of the used zeolite as filler in the zeolite T/ 6FDA-durene MMMs is evident from the fact that these MMMs lie on the Robeson upper bound 2008 (Jusoh et al., 2017b).

MMMs manufactured from continuous phase of cross-linkable co-polyimides viz (6FDA-Durene/DABA (9/1) (MMM-1) and 6FDA Durene/DABA (7/3)) (MMM-2) were fabricated using ZIF-8 nanoparticles. The resulting MMMs were annealed at 400°C which facilitated the cross-linking reaction between the carboxyl groups present in the DABA moiety and thus caused characteristically high suppression in plasticization up to a CO2 pressure of 30 atm. The MMM-1 fabricated with 40 wt. % of additives showed only a slight increase in ideal gas selectivity for CO2/CH4 gas pair in contrast to 134% increase in the same for C3H6/C3H8 gas pair. The loading of 20 wt. % of filler in MMM-1 exhibited CO2/CH4 selectivity to be 19.61 with a striking CO2 permeability value of 728 Barrer in the binary mixture of gases (Askari and Chung, 2013). The experimental results argue upon the stronger dependency of gas pair selectivity and swelling resistance of the MMMs on the optimum annealing temperature and cross-linkable moiety (Askari and Chung, 2013).

The imidazolate likners constituting framework structure of ZIFs render them hydrophobic as a result ZIFs offer better interactions with the polymer matrix (Askari and Chung, 2013). 48 wt. % loading of ZIF-8 particles into ZIF-8/6FDA-DAM MMMs caused 250% increase in permeability and 150% increase in selectivity of propylene/propane (Zhang et al., 2012). The studies have shown that the addition of breathing MOF viz MIL-53(Al), flexible ZIF-8 particles and rigid HKUST-1 MOFs dispersed in a Matrimid alleviated plasticization. Use of exceedingly higher pressures above the plasticization pressure of pristine Matrimid (recorded to be 10–12 bar) produced a slight elevation in the permeabilities of almost all MOF–MMMs in comparison with the neat polymer. Also, the increased MOF loading subsequently increases the plasticization pressure (Shahid and Nijmeijer, 2014).

Ploegmakers et al. (2013) indicated a constant permeability with increase in selectivity of the ethylene/ ethane gas pairs for the respective loading of HKUST-1. This was attributed to the higher diffusion coefficient of gases with sieve in cage morphology.

Increasing the loading of MOF-5 and Ni, Co and Cu doped MOF-5 into the PI as well as the increasing pressure was found to increase the permeability of CH4, CO2 and H2 gases however, the selectivity for all of these three gas pairs viz CO2/CH4, H2/CO2 and H2/CH4 was observed to be reduced. Additionally, significant increase in the rates of permeation was observed for these gases with the use of obtained MMMs combined with a factor of gradual increment in the MOF loadings upto a maximum of 15 wt. % and at constant trans-membrane pressure (100-500 kPa) maintained at room temperature. Increasingly high feed pressures were found responsible for high gas transport via these MMMs (in the order; CH4>CO2>H2) at the cost of reduction in selectivities of all of the above mentioned gas pairs. Here both MOFs had pore sizes in the range of 7-8 Å that were observed to be greater than the intersegmental spaces present within specific polymer chain comprising the MMMs. In fact, the application of trans-membrane pressure in turn increased the permeability of the bigger sized gas molecules specifically CH4 and CO2 that caused a reduction in the selectivities of H2/CO2 or H2/CH4 gas pairs (Ozen and Ozturk, 2019).

Adequate dispersion and good adhesion was observed between the continuous phase and additives in the Matrimid®5218/MIL-53 MMMs especially at lower MOF loadings. MMMs showed slightly increased permeability concerning CH4 as the increasing percentage of filler was embedded. For 20% loading of MIL-53, particles agglomeration and formation of voids was observed that finally led to 300% enhancement in permeability of CH4 over pristine Matrimid membrane but a decrease in separation performance was observed. CO2 permeability was observed to be increased up to 94% with a subsequent growth of 84% in CO2/CH4 selectivity for the MMMs loaded with 15wt. % of fillers in contrast to pure Matrimid membrane.

However, a complete destruction in membrane separation efficiency was observed for 20 wt. % loading of the filler in the MMMs (Dorosti et al., 2014).

Structural transformation of MIL-68(Al) upon water immersion under different sets of conditions followed a crackling core model to transform it to nanosheets of MIL-53(Al) of approximately 150 nm in size. The average thickness of nanosheets was 3.5 ± 0.9 nm. Also the nanosheets of the transformed MOF were disaggregated with an ease using PDMS solution. Both of the prepared fillers were deposited on the asymmetric P84® that was used as support to obtain the supported MMMs by applying vacuum filtration. The MMMs embedded with the filler in the nanosheets form brought improvements in the CO2/CH4 (28.4-28.7 vs. 22.4) and CO2/N2 (19.9-23.2 vs. 17.5) selectivities of the conventional MIL-53(Al)- MMMs with higher CO2 permeance values (Perea-Cachero et al., 2019).

Coating is an efficient method to realize improvements in selectivity of gases. Coating of remarkably permeable silicone polymer layer performed on the surface of Matrimid® 9725 based MMMs embedded with 40 wt. % loading of HKUST-1, MIL-53(Al) and ZIF-8 were observed to overwhelm the likely existence of unselective voids. The CO2/CH4 and CO2/N2 selectivity as well as permeance for both dense and the asymmetric membranes fabricated with the above mentioned MOFs were improved as compared to the unfilled membranes taken as reference due to the breathing mechanism attributed to the MOFs and the interactions of CO2 molecules with the hydroxyl groups present in the frame work (Basu et al., 2011).

The CO2 molecules offer adsorptive interactions with the filler particles Viz NH2-MIL-125 that accounted for the greater separation efficiency of this neat MOF membrane in addition to its role as an additive for the obtained MMMs comprising of Matrimid® 5218. Higher temperatures weakened the adsorptive interactions between the CO2 molecules and amine groups so a decrease in the perm selectivity of CO2 was observed in the thin supported MOF layer. The optimal loading of MOF was found to be 10 wt. % for casting efficient MMMs, capable of exhibiting a concomitant increase in both the selectivity as well as permeability relative to the neat polymer membrane. Whereas slightly increased loading (20 wt. %) of the respective MOF merely promotes permeability. Constant increase in the feed pressure caused no effect on the separation factor of both MMMs. While considering the performance of all of the membranes in relation to the Robeson upper bound and evaluating the performances of the MMMs with the Maxwell- model, it was revealed that all membranes inclusive of the supported thin membrane of MOF exceeded the Robeson upper bound (Friebe et al., 2016).

The combined use of modulation approach and amine-functionalized ligands, is recently being used for preparation of different MOF fillers (Anjum et al., 2015b). This approach is purposely employed so that the MOFs exhibit improved intrinsic separation efficiency and compatibility when present as fillers in MMMs Viz UiO-66@Matrimid ®9725. The amine groups present on the exterior surface of MOF either introduced via the ligand (2-aminoterephthalic acid) or by using suitable modulator (4-aminobenzoic acid) or by combined use of both resulted in formation of covalent linking between the Matrimid® 9724 and the fillers, which yielded precisely stable membranes (Anjum et al., 2015b). Additionally, the MOFs obtained through these approaches possess amine groups inside their pores and intimately offer linker vacancies so as to impart a positive influence on CO2 transport. Here 30 wt. % loading of the MOF was proved to be appropriate towards the formation of MMMs so as to execute exceptional separation efficiency for CO2/CH4 gas mixtures. The resulting MMM exhibited substantially improved permeability of 19.4 Barrer (540%) and mixed gas selectivity of 47.7 (50%) when compared with the pristine Matrimid membrane (Anjum et al., 2015b). A careful and wise selection of the surface organic moiety for a MOF can harvest increased chances to obtain defect-free MMMs. Matrimid® 5218 based MMMs fabricated with surface optimized UiO-66-NH2 particles exhibited improved thermal as well as mechanical properties. Functionalization of UiO-66 with –NH2 and phenyl acetyl groups is known to offer favorable interactions with the imide groups present in the Matrimid® via π-π stacking and hydrogen bonding. On the other hand, robust interactions are expected to occur between the imide groups in the continuous phase and the –NH2 groups. The amide linkages formed through hydrogen bonds are shown in Figure 4. So that truly defect free Polymer/ filler interface could be obtained.

 

 

The obtained results indicated ~200% increase in CO2 permeability and ~ 25% increase in ideal selectivity for CO2/N2 than the pure Matrimid®. These improvements were due to the molecular sieving offered by the MOF particles thus confirming the achievement of the anticipated technique so as to alleviate the defective MOF/Matrimid® interfaces (Venna et al., 2015).

The fast solvent removal from NH2-MIL-53(Al)@PI MMMs (25 wt. % of filler) of different thicknesses favorably contracted the MOF structure to a framework configuration possessing narrow pore size which then enhanced CO2 permeability at trans-membrane pressure difference of 3 bar and 308 K and preserving the relatively high separation factor. Increased CO2 permeability was also observed due to the same reason. These investigations revealed that even higher filler loadings (up to 25 wt%) did not affect the previously established exceptionally good filler polymer contact, while possessing void volume fraction to be almost 0.11% (Rodens et al., 2014).

High performance MMMs doped with ZIF-94 as filler into the 6FDA-DAM polymer matrix are known to selectively separate the CO2 from a mixture of gases testing (15CO2:85N2) at room temperature with a trans-membrane pressure difference ranging between 1-4 bar. The addition of ZIF-94 particles caused an increase in CO2 permeability through the membrane system while sustaining a constant selectivity (~22) for CO2/N2 gas mixture. The biggest increase of~ 200% was observed in CO2 permeability for 40 wt. % loading of ZIF-94 into the continuous phase thus paving its way towards the highest ever reported permeability of 2310 Barrer while sustaining quite similar selectivity among the 6FDA-DAM MMMs. The ZIF-94 MOF crystals used in this work were prepared for the first time possessing smaller particle size (< 500 nm) by using methanol and THF that are termed as nonhazardous solvents instead of using DMF in a scalable process. These results demonstrated a very good dispersal and sufficient interaction of the filler particles even at their high loadings in the layer of continuous phase (Etxeberria-Benavides et al., 2018).

High-performance ZIF-8/MMM were produced using in-situ controlled thermal treatment that was performed in air at a temperature 350°C in the presence of air to remarkably boost the gas separation performance up to the highest ever reported selectivity for CO2/CH4 to date for the MMMs loaded with MOFs (Kertik et al., 2017). The amorphisation of the MOF occurred due to the protection of the surrounding continuous phase that in-situ created a porous molecular sieve network. Role of the thermal treatment unveiled when it improved the adhesion between filler and continuous phase and together induced oxidative cross-linking of the continuous phase. Thus increasingly stable MMMs were formed that offered plasticization resistance at considerably higher pressure of 40 bar (Kertik et al., 2017). Hence, the Matrimid® membranes displayed a substantial increase in selectivity of CO2/CH4 from a range of 22 to 40 at 250°C. While annealing at 350°C increased the selectivity nearly 4 times than the reference pristine Matrimid® films (selectivity of CO2/CH4 = 20) (Kertik et al., 2017). However, annealing at shorter applied treatment times at 350°C yielded lower selectivities (Kertik et al., 2017) and MMMs treated at low temperatures range of 100-160°C did not exhibit well enhanced selectivity (Kertik et al., 2017).

The thermally treated MMMs embedded with 20 wt. % loading of ZIF-8 at temperature range of 100- 160°C exhibited permeabilities of 20 Barrer that were more than twice the permeability (8 Barrer) of reference Matrimid® film. The higher ZIF-8 loading in the range of 30 to 40 wt. % ended up with achievement of permeability up to 57 Barrer. An increase in CO2 permeabilities was attributed to the defects created at the interface of continuous phase and ZIF-8 nanoparticles in addition to the residual DMF entrapped within ZIF-8. The continuous phase in this study underwent densification after cross-linking which subsequently decreased the permeability of CH4 while the CO2 permeability was affected to a much lesser extent and thus resulted in general improvement in CO2/CH4 selectivity (Kertik et al., 2017). The building blocks of non-crystalline ZIF-8 filler acted as virtual source for rich abundance of imidazolate linkers and unsaturated Zn2+ ions which could further promote the robust quadrupolar interactions with CO2 (Hu et al., 2013).

Another report describes (Castro-Muñoz et al., 2019) use of 30 wt. % ZIF-8 particles as fillers for fabrication of Matrimid MMM which exhibited improved CO2 permeability (33.3 Barrer) and selectivity (15.4). Similarly, the molecular sieving characteristic of MOF-76(Y) also improved the CO2/CH4 and CO2/N2 selectivity of the Matrimid ®5218 MMMs (Bano et al., 2019). LaBTB/6FDA-DAM based MMMs are also reported to be potential candidate for selective CO2 capture even under water/moisture and these have surpassed the 2008 Robeson’s upper bound (Hua et al., 2018).

1.3 Polysulfone (PSf)

Polysulfone (PSf) is a characteristically high-strength, transparent tough and rigid thermoplastic polymer with good thermal and chemical stability over temperatures ranging broadly from -100°C to above 160°C. The exceptionally high mechanical strength and superb oxidative resistance render it a favored material to be used as a membrane substrate. It is extensively used in fabricating membranes for applications in ultra-filtration systems for water (Kaeselev et al., 2001; Kilduff et al., 2000) and the gas separations Liu et al. (2004) such as heterogeneous MMMs based on PSf which were prepared with copper terephthalate (CuTPA) particles.

PSf embedded with amine-impregnated zeolite particles were observed to be more selective towards CO2 over methane as compared with pristine PSf module (Castruita-de León et al., 2020). Similarly, three different kinds of CuTPA particles each with varying pore size distribution, pore volume and surface areas were used as inorganic dispersed phase. CuTPA particles having high porosity increased the permeability values of the heterogeneous membranes to He, N2, O2 and CO2. Comparatively, a decrease in permeability was recorded for the two other variants of CuTPA particles possessing characteristically lower porosity. The annealing of the resulting MMMs embedded with greatly porous CuTPA particlesat a temperature of 200°C resulted in CO2 permeability that was 3.3-times greater than the reference PSF film. The MMMs annealed at 150°C also exhibited 1.65-times higher permeability for CO2 than reference PSF film. The substantial improvement in membrane permeability was related to the removal of residual solvent from pores of CuTPA particles after annealing (Kubica et al., 2016).

Ordered mesoporous silica (OMSs) particularly MCM-41 (Kim and Marand, 2008) and the other commercially employed MCM-48 (Kim et al., 2006b) are known to effect positively towards the permeability of unfilled PSF membranes while sustaining the selectivity at the same time. This suggests enhanced interactions with the continuous polymer phase which positively affects the sieving effect derived from the mesoporosity (2-3 nm) present in them. The small quantities of such ordered mesoporous silica spheres (MSS) or exfoliated layered microporous titanosilicate such as UZAR-S1 (produced from JDF-L1, a layered material) are reported to be used as inorganic fillers into PSf Udel® P-3500 matrix (Zornoza et al., 2011). The embedding of MSS in quantities as low as 8 wt. % to fabricate the MSS–PSf MMMs resulted in specifically pronounced increase in selectivities of H2/CH2 (79.2) and CO2/N2 (36.0) gas mixtures and permeability values as well for H2 (26.5 Barrer) and CO2 (12.6 Barrer). UZAR-S1-PSf membrane loaded with 4 wt. % of filler executed H2 permeability of 11.5 Barrer and H2/CH2 gas pair selectivity value to be 69.2. The mesoporous phase favored H2 diffusivity instead of CH2, while the increased permeability was credited to the disruption of polymer chain packing which led to an increment in polymer-free volume (Zornoza et al., 2011).

Reid et al. (2001) recorded positive impact of large pore sized MCM-41 when used as an additive for PSf (Reid et al., 2001) on the permeability value of CO2 while selectivity stayed unchanged. Kim and Marand (2008) described that 40 wt. % nanosized (80 nm) MCM-41 loading into the PSf caused 300% increase in permeability of CO2 Kim and Marand (2008). However, the functionalized silica particles slightly improved the CO2/CH4 selectivity (Sakamoto et al., 2007). Also, the increased void formation upon 8 wt. % loading of mesoporous silica resulted in a decreased selectivity of the PSf based MMMs (Zornoza et al., 2009).

The silanol groups on the exterior surface of 3D MCM-48 offer good interactions with PSf matrix which in turn increased the permeability without compromising the selectivity (Kim et al., 2006b).

Mesoporous silica particles extracted from rice husk ash were functionalized with 4-aminophenazone (4-AMP) so as to improve the CO2-philic characteristics of the resulting PSf based MMMs. The filler particles were well adhered and nicely dispersed into the continuous phase. The presence of large mesopores in the filler caused relatively quicker diffusion of the penetrant gas that was accountable for the high gas permeabilities of all MMMs compared to pristine PSf membrane. The presence of functionalized silica at a highest 40% loading in the MMMs caused them to exhibit considerably higher ideal selectivities for CO2/CH4 (32.79) and CO2/N2 (33.31) pairs than the un-functionalized silica based MMMs and pristine PSF membranes.

Change in temperature caused a direct effect on the free volume which in turn affected the flexibility of the polymer chains and that caused faster diffusion of molecules and so higher chain mobility of the polymer matrix and hence permeability of CO2 was pronouncedly increased. The same factors were responsible for the decreased selectivity of the CO2 through the MMM of the same composition. The use of such extremely ordered structures possessing small but straight pore channels provide improvement in gas permeation properties thus warranting the silica extracted from the rice husk to be a promising additive for commercial gas separation processes under variable temperature conditions (Waheed et al., 2016).

The performance of acrylate derivatization on PSf (PSfAc) to obtain a series of MMMs fabricated by using amine functionalized mesoporous MCM-41(NH2-MCM-41) resulted in a good contact between the aminated silica and PSfAc matrix (Khan et al., 2013b). The covalent linkages were formed between functionalized silica and PSf, that enhanced the permeability of PSfAc-NH2-MCM-41 series of MMMs slightly due to three factors i.e., rigidification of polymer chains at the interface, (Zhang et al., 2008), reduced pore size offered by surface functionalized fillers and elimination of the immensely permeable unselective voids. So the improved gas performance for the (selectivity of CO2/N2 (32.97) and CO2/CH4 (31.48) gas, and CO2 permeability (9.13) Barrer) was observed (Khan et al., 2013b).

ZIFs possess tunable pore structure with well famed thermal and chemical stabilities (Phan et al., 2010). The 0.5 wt. % loading of ZIF-8 in PSf matrix caused 1.37 fold increase in CO2 permeation and 1.19 fold increase in selectivity due to creation of increase free volume within polymer chains. However, a dramatice decrease in selectivity was observed upon increasing the filler loading upto 10 wt. % due to non-selective channeles formed within PSf layers (Nordin et al., 2015)

The presence of a number of active sites in ZIF-108 makes it able to accommodate substitutions offered from other metals. The doping of ZIF-108/PSF MMMs using Cobalt as secondary metal executed almost a 7-fold enhancement in CO2 permeability over ZIF-108/PSf and a 17-fold higher permeability of the same than the pure PSf membrane. The doped metal in fact enlarged the pore size in ZIF-108 framework which in turn increased the filler compatibility with the continuous phase so as to achieve superior separation factors and improved permeability of CO2 (Ban et al., 2014).

The combined use of ZIF-8 and MIL-101(Cr) in 1:1 ratio for fabrication of MMMs consisting of Polysulfone harvested 500% increase in CO2 permeability in the resulting MIL-101(Cr)/ZIF-8@PSF MMMs over the pure PSf due to the synergistic effects of membrane with combined fillers with the same CO2/CH2 selectivity. The ZIF-8/PSf executed about 300% increase and the MIL-101(Cr)/PSf based MMMs exhibited 260% increment in CO2 permeability than that of the control (Jeazet et al., 2016).

Similarly, dispersion of hybrid GO/ZIF-302 into the PSf matrix caused improved CO2 permeability and a 2-fold increase in CO2/N2 selectivity as a result of better interaction of the hybrid filler with the polymer matrix (Sarfraz and Ba-Shammakh, 2016a, b).

Similarly, incorporation of MIL-101 (Al) caused 60% increase in gas permeability in the PSf based MMMs with selectivity remained unchanged (Rodens et al., 2014).

Ishaq et al developed high performance MMMs comprising of nano bars of Bio-MOF-1 and PSf matrix. The resulting MMMs obtained after 30 wt. % loading with Bio-MOF-1 showed 168% increase in CO2 permeability (16.57 Barrer) and 58% increase in ideal selectivity of (42.6 and 45.6 for CO2/CH4 and CO2/N2) as compared to the unfilled reference membranes. The Bio-MOF-1 created additional channels upon loading into the PSf matrix thus the concomitant increase in free volume of membrane facilitated the diffusion of gas molecules via the MMMs which in turn positively influenced the permeability.

The existence of pyrimidine and adeninate amino Lewis basic sites decorate the pores and thus offer reasonably contracted pore dimensions in the Bio-MOF-1 so as to greatly increase the adsorption of the CO2 gas molecules with increased selectivity (Ishaq et al., 2019)

Similarly, NH2-MIL-125 (Ti)/ PSf MMMs also show better gas permeability and selectivity as compared to pristine membranes (Anjum et al., 2016).

The appropriately textured nanosized UiO-66-GO hybrids in size range 30– 100 nm were embedded into the PSF to obtain MMMs with varying quantities of 0 and 32 wt. %. A good hybrid filler-polymer interaction, the barrier effect offered from the GO and the micro porous nature of the MOF were found responsible to affect the separation phenomena in different MMMs. An increase in temperature from 30 to 90°C positively influenced the permeability of all test gases with a simultaneous decline in the corresponding selectivity of H2/CH4 and CO2/CH4 mixtures (Castarlenas et al., 2017).

The highly stable sulfonated UiO-66 MOFs employing the zirconium metal were grafted by using silane coupling agent namely mercaptopropyl trimethoxysilane. They were then used to fabricate the PSf based MMMs along with the non functionalized UiO-66. The modified sulfonated UiO-66 functionalized with silane, adhered properly with the continuous phase. Thus there was a higher affinity of the same filler towards the CO2 gas molecules upon increasing concentration of the sulfonic group which in turn improved the selectivity and CO2 permeability for pure and mixed gases. The resulting PSf based MMMs employing functionalized sulfonated UiO-66 exhibited high separation performance that were very close to the Robeson upper bound when compared with several other MMMs of such kind. Thus the functionalized MOFs are assumed as efficient materials for gas separation purposes (Tahir et al., 2019).

1.4 Miscellaneous polymer based MMMs

A number of other polymers are also tested for fabrication of MMMs by embedding of various kinds of fillers into them. The examples include Sulfonated poly (etheretherketone) (SPEEK) which is a polyelectrolyte and is considered to be a potential candidate for gas separation applications (Khan et al., 2011). Figure 5 illustrates structure of SPEEK. The glassy SPEEK membranes involved facilitated transport as an efficient method to influence positively their CO2 separation efficiency by reversible reaction between CO2 molecules and facilitated transport carriers (Shen et al., 2013; Zhang et al., 2013).

 

 

MIL-101 (Cr) exhibits high CO2 adsorption capacity and stability in water and it is found to retain its morphology upon sulfonation (S-MIL-101(Cr)) or embedding within the SPEEK matrix to form MMMs. The gas performance measurements indicated that the addition of SPEEK/S-MIL-101 and SPEEK/MIL-101caused an increase in the selectivity of the resulting MMMs for CO2/CH4 and CO2/N2 systems by positively affecting the CO2 solubility. The maximum value of ideal selectivity obtained for CO2/CH4 was 50 and for CO2/N2 system was 53, CO2 permeability was 2064 Barrer in humidified state. The water molecules present in bound state facilitate the hydration of CO2 resulting in its easy permeation through the membrane module with a sufficiently lower energy barrier. As a result, in humidified state, comparatively low transport resistance offered towards CO2 as compared with N2 and CH4 and hence high CO2/gas selectivity is obtained (Xin et al., 2015).

Compared with the unfilled SPEEK membrane, the MMMs embedded with 40 wt. % MIL-101(Cr) and S-MIL-101 (Cr) exhibited an increase in CO2 solubility coefficient by 39% and 61%, correspondingly. Moreover, the quadrupole moment of CO2 and availability of extra polar interaction sites of –SO3H were found responsible for higher values of solubility selectivity of SPEEK/S-MIL-101 MMMs as compared with SPEEK/MIL-101 MMMs. Furthermore, the MMMs embedded with 40 wt. % sulfonated MIL-101 showed a corresponding increase of 74% and 38% in the CO2/CH4 and CO2/N2 selectivities in contrast with the MMMs embedded with same loading of unmodified MIL-101 (Xin et al., 2015).

The MMMs of SPEEK/S-MIL-101 series executed increased CO2 permeability in comparison with the MMMs doped with the non-sulfonated MOFs as a result of reduced chain rigidification and increased size of ionic nano-channel of the SPEEK/S-MIL-101 MMMs, the increased total water and the higher solubility of CO2 (Xin et al., 2015).The mixed gas CO2 permeability and CO2/CH4 as well as CO2/N2 system’s selectivity were observed to be slightly lower as compared with the results of pure gas tests for both dry and humidified membranes. The primary reason for improved results in case of mixed gas systems may be the competitive sorption effect (Raymond et al., 1993) as the CO2 pressure did not reached up to the plasticization pressure (Xin et al., 2015) during gas separation experiments.

The CO2 permeability was observed to be increased with the temperature while the opposite was found true for the selectivities of CO2/CH4 and CO2/N2 systems. MMMs embedded with sulfonated MOFs exhibited fairly good gas separation efficiency surpassing the Robeson’s upper bound reported in 2008 in their humidified state. Conclusively, the use of exceedingly permeable MOFs and tuning their functional groups effectively improved their contact and affinity with the continuous phase thereby making it possible to execute improved gas separation performance of the pristine polymer (Xin et al., 2015).

Fluorinated and sulfonated Polyether ether ketones are prospective candidates for membrane based separation of CO2. This property is the result of their effective chain packing and reduced formation of charge transfer complexes that renders an increased free volume and permeability (Calle et al., 2010; Ayala et al., 2003). Incorporation of zeolite 4A into fluorinated sulfonated poly (ether ether ketone) polymer (F-SPEEK) having fixed degree of sulfonation yielded perm-selectivities closer to the Robeson’s upper bound along with the execution of superior anti-plasticization properties (Tahir et al., 2018).

Tahir et al fabricated MMMs containing F-SPEEK (prepared through 4, 4-difluorobenzophenone (m), sodium 5, 5′-carbonylbis (2-fluorobenzene-sulfonate) (n), and 4, 4¢-difluorobenzophenone (DFBP)) using zeolite 4A filler. Zeolite 4A with a distinctive pore size ca. 3.8Å that possesses a potential to perform as a molecular sieve with high mechanical, and thermal stability. The cubic-structured alumino silicates are also present here with ordered cavities and channels for the penetration of ions and molecules. The zeolite 4 A possess unit cell with high negative charge due to presence of AIO45– and SiO44– which is guilty of cationic propagation and thus eventually causes a better adsorption. The higher selectivity was obtained for CO2/CH4 and CO2/N2 systems, as a result of synergistic behavior of F-SPEEK/zeolite 4A. The facilitation ratio of all of the three gases increased with the filler loading. Consequently, each gas experienced an increase in permeability through the membrane. The separation performance results of these membranes were found closer to the Robeson upper bound in contrast with other such MMMs (Tahir et al., 2018).

Another example of polymer used for formation of MMMs is Chitosan (CS), poly (β (1→4) 2 amino 2 deoxy D glucopyranose). is an abundantly available, cheaper in cost and linear polysaccharide that is obtained by deacetylation of chitin. It is usually acquired from certain renewable natural sources, i.e. the shell of crustaceans so it is biodegradable, biocompatible and non-toxic as well as hydrophilic in nature. Casado-Coterillo et al. (2015) combined a small quantity of non-toxic and highly absorbing ionic liquid viz (emim)(Ac) (IL) with the CS and embedded them with HKUST-1 and ZIF-8 particles of nanometer size so as to prepare MMMs. The molecular sieving ability of ZIF-8 particles was found to be due to the presence of cavities that were11.6 Å in diameter and were connected through small apertures of 3.4 Å. Presence of IL and ZIF-8 improved the thermal stability in addition to the ability of retaining a water content of about 20 wt. %, featuring the successful development of high temperature water resistant membranes for CO2 separation. The MMMs with 10 wt. % ZIF-8 and 5 wt. % HKUST-1/IL-CS membranes were observed to show correspondingly best CO2 permeability and CO2/N2 selectivity performance recorded as high as 5413 ± 191 and 11.5, and 4754 ± 1388 Barrer and 19.3, respectively. This was attributed to a better adhesion and smaller particle size of ZIF-8 than HKUST-1 nanoparticles with respect to the IL-CS continuous phase, as inferred by Hansen solubility parameters and Maxwell-based models that were modified to account for pore blockage, rigidification, and crystallinity of the CS matrix, with exactly precise predictions (Casado-Coterillo et al., 2015).

PBI is another polymer that is extensively used for formation of MMMs. Hafnium based UiO- 66-type MOF formulated as UiO-66(Hf)-(OH)2 possess distinct nanoparticle size and exhibited good compatibility with (PBI) in the resulting MMMs (Hu et al., 2016a). When compared with UiO-66(Zr), the UiO- 66(Hf)-(OH)2 showed a smaller BET surface (922 m2 g−1) area and reduced pore sizes at ∼4 Å, most probably due to the introduction of heavier Hf cations and relatively bulkier linkers (Hu et al., 2016b). But the unexpected, high gravimetric uptake of CO2 (4.06 mmol g−1) and volumetric uptake of CO2 (167 v/v at 1 bar and 298 K) exhibited by this MOF was among the highest of all the water-stable pristine MOFs, without chemical decorations (e.g., amine grafting). The embedding of 10 wt. % of these MOF particles into the PBI matrix has resulted into the outstanding gas permeability and selectivity values which has put this membrane above the 2008 Robeson upper bound (Hu et al., 2016b).

It was found that elevated pressure and reduced temperature promoted the gas separation efficiency of the PDMS MMMs embedded with microporous adsorptive carbon nanoparticles as the penetrant gas molecules can follow the capillary condensation through the micropores within the filler particles that were embedded in these MMMs (Heidari et al., 2019). Similarly, HKUST-1@PDMs (Zulhairun, et al., 2015) and ZIF-8@PDMS (Fang et al., 2015) acted as increasingly good adsorptive filler into the PDMS matrix for improved CO2 and higher hydrocarbons respectively.

Similarly, PIM fabricated with unfunctionalized and nano MIL-101 (ca. 50 nm) strongly shifted the permeability towards higher values for all gas pairs, specifically for CO2 i.e. up to 35,600 Barrer, highest among the PIM-1 based MMMs while selectivity remained almost same (Khdhayyer et al., 2019).

Similarly, nanosized ZIF-8 crystals with varying particle sizes exhibit different capacities of gas permeability and selectivity upon embedding into the PES matrix. A ternary component of ZIF-8/PES/pNA which consisted of 10 wt. % of ZIF-8 particles exhibited CO2/CH4 selectivity 52.6 at 35°C (Ayas et al., 2018).

Embedding of different MOFs into the poly (vinylidene fluoride) (PVDF) phase such as CuBTC @ PVDF, CuBDC @ PVDF, MIL-53 (Al) @ PVDF and NH2-MIL-53(Al) @ PVDF MMMs has witnessed improvement in the gas separation performance. This improvement is explained to the chain rigidification induced due to the Cu BDC (Feijani et al., 2015). Further, more than 100% increase in gas selectivity for the He/CH4, He/N2 and CO2/CH4 systems was observed for the PVDF MMMs that were fabricated with CuBDC in along with GO nanosheets. These MMMs exhibited homogeneous dispersal of fillers, nice polymer/filler interactions and filler morphologies (Feijani et al., 2018).

Poly (ether block amide) commercially available with the brand name of PEBAX is one of the outstanding polymers employed for separation of gases particularly CO2. Its structure constitutes polyamide (PA) part possessing extraordinarily increased hardness and exceptional mechanical resistance as shown in Figure 6. On the other hand, the flexible PE segment contributes towards permeability (Tocci et al., 2008; Reijerkerk et al., 2010) particularly for the polar gas species like CO2 due to the interactions of ether group of the flexible segment with the CO2 molecules (Lin and Freeman, 2005). So, relatively improved diffusion and adsorption is obtained for this molecule in comparison with the non-polar gases. Many different MOFs e.g. ZIF-7 (Sutrisna et al., 2018), Cu-MOF (Kim et al., 2016b), MIL-53 (Meshkat et al., 2018), UiO-66 (Sutrisna et al., 2018), 7.5wt. % MOF- 801@PEBA (Sun et al., 2019) as well as FeBTC/PEBAX (Dorosti and Alizadehdakhel, 2018) and many other inorganic fillers such as Attapulgite (Xiang et al., 2016), Carbon nanotubes (Zhao et al., 2017), Graphene oxide (Zhao et al., 2015), silica (Ariazadeh et al., 2020) and Zeolite 4A (Murali et al., 2014) were previously reported to fabricate MMMs using PEBA.

 

 

Polyurethane (PUR) is a block copolymer including a soft but rubbery segment (SS) which is able to impart increasingly good permeability properties along with a hard but glassy part (HS) (Figure 7) meant to introduce suitable mechanical properties. A decent combination of both these segments results in robust mechanical structure that may seldom compromise over the amount of permeability concerning the resulting PUR membranes (Hepburn, 2012; Isfahani et al., 2016a).

 

 

ZSM-5, silica nanoparticle, and ZIF-8 sufficiently interact with these segments to bring a change in the balance of hydrogen bonding between the both segments (Amedi et al., 2016). The cross-linking property of Silica particles resulted in decreased free space within polymer. Consequently, increased selectivity of carbon dioxide to methane was observed from 15.9 to 23.4 (Amedi et al., 2016).

The low cost PU/ZIF-8 MMMs exhibited a proper permeability of 74.6 barrer. The increasing amount of zeolite particles inside the PUR membrane could lead to compliance of two different behaviors. Firstly, the 5% improvement in performance of MMM was observed by addition of ZSM-5 particles so as to cause some void space around the particle that increased the sorption selectivity. But the mobility selectivity remained constant as the pore size of these particle was (5 Å) but larger than the kinetic diameter of the both gases. But on overall selectivity was increased.

The second behavior was related to the increase in amount of particles from 5% to 20% with a consequence of increase in permeability of carbon dioxide at its compromised selectivity due to CO2 plasticity which brought an ease in the mobility of continuous phase of PUR that increased empty spaces between the PU chains. Thus creation of voids pores and the particle aggregation positively affected permeability of the large CH4 molecules. The permeability of CO2 molecules on the other hand was decreased as a result of decreasing molar fraction of CO2, existence of methane in the pure feed and the course of permeation and dissolution phenomena are followed by existence of competition between the species (Amedi et al., 2016).

Similarly, Gholami et al. (2017) reported that ZIF-8/PU MMMs showed increased thermal stability, improved tensile strength and strain at break (Gholami et al., 2017). CO2 and CH4 transport was positively affected upon incorporation of ZIF-8 as additive into the PU matrix which resulted in significant improvement in separation performances of all of the tested membranes in their work. (Gholami et al., 2017).

Likewise, Ismail et al. (2011) also incorporated 0.5-3 wt. % loadings of the un-functionalized MWCNTs into the polyethersulfone matrix. Their results revealed that attainment of highest gas selectivity (α) (αCO2=CH4 = 250:13; αO2=N2 = 10:65) was possible with the use of 0.5 wt. % loading of MWCNTs. The gas selectivity showed a decline upon addition of 3 wt. % of the MWCNTs as a result of formation of interfacial voids and the higher loading of MWCNTs content made them more prominent.

In view of considerations laid in the literature review section, the present study was formulated to prepare the MOF based MMMs as the polymer and explore their CO2 separation potential for CO2/CH4 pair.

 

Conclusions and Recommendations

Cellulose acetate, polyimide and polysulfone were discussed here as chief polymer matrices for the MMMs with a brief discussion on some other polymer matrices. A number of different fillers have been used in order to improve the separation properties of the resulting MMMs, and to find one that could surpass the Robeson’s upper bound and to remove or decrease the shortcomings of the pure polymers or inorganic membranes, cost effectiveness and to make the resulting MMMs as viable commercial candidate in the field of MMMs based separation. After going through the practical applicability of various fillers, it was found that although other fillers like silica or titania nanoparticles, activated charcoal, silane based modified fillers, and amino functionalization of various fillers result in the improvement in the efficiency of resulting MMMs after their embedding in different polymer matrices, the MOFs have their own chemistry with the different polymer matrices. They are also proved to be affective filler towards various polymer matrices due to their porosity, sieving effect and thereby offering the facilitated transport through the MMMs. The brittleness, cracks and voids in the resulting MMMs were found to be compromised and so, improved permeability and selectivity could be obtained by careful selection of MOF-polymer pair. Nicer distribution and compatibility with the polymer and plasticization resistance shown by different resulting MMMs tested argue upon their usefulness in the field of separation. Surface functionalization and use of some other filler as co-filler can further improve the separation efficiency. In view of considerations laid in the literature review section, a study can be formulated including preparation of the MOF based MMMs as the polymer and their CO2 separation potential for CO2/CH4 pair can be explored. There are ample possible polymer-MOF pairs available in the literature which can be tested experimentally to fully explore their potential in this field. In this context our research group has studied MMMs comprising of Matrimid® 5218 incorporating Tb(BTC)(H2O).(DMF)1.1 MOF with three different percentages for selective separation of CO2/CH4 (Tariq et al., 2020). Such studies can lead to the selection of most suitable MOF for the commercial applicability of the selected MMMs embedded with optimum loadings of the most appropriate MOF.

 

Novelty Statement

This review article highlights the gas separation performance applications of mixed matrix membrane technology and their industrial applicability.

 

Author’s Contribution

Misbah Sultan and Tariq Mahmud presented the idea regarding content of the article, Asma R. Tariq collected data and wrote the article and Saadia R. Tariq performed proof reading and language correction of the article.

Conflict of Interest

The authors have declared no conflict of interest.

 

References

Abedini, R., Mousavi, S.M. and Aminzadeh, R., 2011. A novel cellulose acetate (CA) membrane using TiO2 nanoparticles: Preparation, characterization and permeation study. Desalination, 277(1-3): 40-45. https://doi.org/10.1016/j.desal.2011.03.089

Abedini, R., Omidkhah, M. and Dorosti, F., 2014. Highly permeable poly (4-methyl-1- pentyne)/NH2-MIL-53 (Al) mixed matrix membrane for CO2/CH4 separation. RSC Advances, 4(69): 36522-36537. https://doi.org/10.1039/C4RA07030E

Achoundong, C.S.K., Bhuwania, N., Burgess, S.K., Karvan, O., Johnson, J.R. and Koros, W.J., 2013. Silane modification of cellulose acetate dense films as materials for acid gas removal macromolecules, 46(14): 5584-5594. https://doi.org/10.1021/ma4010583

Adatoz, E., Avci, A.K. and Keskin, S., 2015. Opportunities and challenges of MOF-based membranes in gas separations. Separation and Purification Technology, 152(September): 207–237. https://doi.org/10.1016/j.seppur.2015.08.020

Adeeb, S., Lukman, A., Shah, N.S.M. and Hamzah, S.A., 2018. Joint transmit antennas for energy efficiency in downlink massive MIMO systems. International Journal of Integrated Engineering, 10: 27-31.

Ahmad, A.L., Jawad, Z.A., Low, S.C. and Zein, S.H.S., 2014. A cellulose acetate/multi-walled carbon nanotube mixed matrix membrane for CO2/N2 separation. Journal of Membrane Science, 451(February): 55-66. https://doi.org/10.1016/j.memsci.2013.09.043

Ahnfeldt, T., Guillou, N., Gunzelma, D., Margiolaki, I., Loiseau, T., Férey, G., Senker, J. and Stock, N., 2009. (Al4(OH)2(OCH3)4(H2N-bdc)3). x H2O: A 12-connected porous metal-organic framework with an unprecedented aluminum-containing brick. Angewendte Chemie International Edition England, 48(28): 5163-5166. https://doi.org/10.1002/anie.200901409

Amedi, H.R. and Aghajani, M., 2016. Gas separation in mixed matrix membranes based on polyurethane containing SiO2, ZSM-5, and ZIF-8 nanoparticles. Journal of Natural Gas Science and Engineering, 35(September): 695-702. https://doi.org/10.1016/j.jngse.2016.09.015

Amooghin, A.E., Omidkhah, M. and Kargari, A., 2015. Enhanced CO2 Transport Properties of Membranes by embedding nano-porous zeolite particles into Matrimid®5218 matrix. RSC Advances, 5(12): 8552-8565. https://doi.org/10.1039/C4RA14903C

Anjum, M.W., Bueken, B., De Vos, D. and Vankelecom, I.F.J., 2016. MIL-125(Ti) based mixed matrix membranes for CO2 separation from CH4 and N2. Journal of Membrane Science, 502(March): 21-28. https://doi.org/10.1016/j.memsci.2015.12.022

Anjum, M.W., de Clippel, F., J. Didden, Khan, A.L., Couck, S., Baron, G.V., Denayer, J.F.M., Sels, B.F. and Vankelecom, I.F.J., 2015a. Polyimide mixed matrix membranes for CO2 separations using carbon-silica nanocomposite fillers. Journal of Membrane Science, 495(December): 121-129. https://doi.org/10.1016/j.memsci.2015.08.006

Anjum, M.W., Vermoortele, F., Khan, A.L., Bueken, B., De Vos D.E. and Vankelecom, I.F.J., 2015b. Modulated UiO-66 based mixed matrix membranes for CO2 separation. ACS Applied Materials and Interfaces, 7(45): 25193-25201. https://doi.org/10.1021/acsami.5b08964

Ariazadeh, M., Farashi, Z., Azizi, N. and Khajouei, M., 2020. Influence of functionalized SiO2 nanoparticles on the morphology of CO2/CH4 separation efficiency of Pebax-based mixed matrix membranes. Korean Journal of Chemical Engineering, 37(2): 295-306. https://doi.org/10.1007/s11814-019-0350-7

Aroon, M.A., Ismail, A.F., Montazer-Rahmati, M.M. and Matsuura, T., 2010. Effect of raw multi-wall carbon nanotubes on morphology and separation properties of polyimide membranes. Separation Science and Technology, 45(16): 2287-2297. https://doi.org/10.1080/01496395.2010.484007

Askari, M. and Chung, T.-S., 2013. Natural gas purification and olefin/paraffin separation using thermal cross-linkable co-polyimide/zif-8 mixed matrix membranes. Journal of Membrane Science, 444(October): 173-183. https://doi.org/10.1016/j.memsci.2013.05.016

Ayala, D., Lozano, A., Abajo, Garcıa-Perez, C., De la Campa, J., Peinemann, K.-V., Freeman, B. and Prabhakar, R., 2003. Gas separation properties of aromatic polyimides. Journal of Membrane Science, 215(1-2): 61-73. https://doi.org/10.1016/S0376-7388(02)00602-6

Ayas, İ., Yilmaz, L. and Kalipcilar, H., 2018. The gas permeation characteristics of ternary component mixed matrix membranes prepared using ZIF-8 with a large range of average particle size. Industrial Engineering and Chemistry Research, 57(7): 16041-16050. https://doi.org/10.1021/acs.iecr.8b02440

Bae, T.-H., Liu, J., Lee, J. S., Koros, W. J., Jones, C. W. and Nair, S., 2009. Facile high-yield solvothermal deposition of inorganic nanostructures on zeolite crystals for mixed matrix membrane fabrication. Journal of American Chemical Society, 131(41): 14662-14663. https://doi.org/10.1021/ja907435c

Baker, R.W., 2002. Future directions of membrane gas separation technology. Industrial and Engineering Chemistry Research, 41(6): 1393-1411. https://doi.org/10.1021/ie0108088

Balçik, M. and Ahunbay, M.G., 2018. Prediction of CO2-induced plasticization pressure in polyimides via atomistic simulations. Journal of Membrane Science, 547(February): 146−155. https://doi.org/10.1016/j.memsci.2017.10.038

Ban, Y., Li, Y., Peng, Y., Jin, H., Jiao, W., Liu, X. and Yang, W., 2014. Metal-substituted zeolitic imidazolate framework ZIF-108: gas-sorption and membrane-separation properties. Chemistry A European Journal, 20(36): 11402–11409. https://doi.org/10.1002/chem.201402287

Bano, S., Tariq, S.R., Ilyas, A., Aslam, M., Bilad, M.R., Nizami, A.S. and Khan, A.L., 2019. Synergistic solution of CO2 capture by novel lanthanide-based MOF-76 yttrium nanocrystals in mixed-matrix membranes. Energy and Environment, 31(4): 692-712. https://doi.org/10.1177/0958305X19882413

Basu, S., Cano-Odena A. and Vankelecom, I.F.J., 2011. MOF-containing mixed-matrix membranes for CO2/CH4 and CO2/N2 binary gas mixture separations. Separation and Purification Technology, 81(1): 31-40. https://doi.org/10.1016/j.seppur.2011.06.037

Bos, A, Pünt, I.G.M., Wessling, M. and Strathmann, H., 1999. CO2-induced plasticization phenomena in glassy polymers. Journal of Membrane Science, 155: 67-78. https://doi.org/10.1016/S0376-7388(98)00299-3

Bouma, R.H.B., Checchetti, A., Chidichimo, G. and Drioli, E., 1997. Permeation through a heterogeneous membrane: the effect of the dispersed phase. Journal of Membrane Science, 128: 141-149. https://doi.org/10.1016/S0376-7388(96)00303-1

Calle, M., Lozano, A.E., de Abajo, J., José, G. and Álvarez, C., 2010. Design of gas separation membranes derived of rigid aromatic polyimides. 1. Polymers from diamines containing di-tert-butyl side groups. Journal of Membrane Science, 365(1-2): 145-153. https://doi.org/10.1016/j.memsci.2010.08.051

Caro, J., 2011. Are MOF membranes better in gas separation than those made of zeolites? Current Opinion in Chemical Engineering, 1(1): 77-83. https://doi.org/10.1016/j.coche.2011.08.007

Caro, J., Noack, M., Kölsch, P. and Schäfer, R., 2000. Zeolite membranes-state of their development and perspective. Microporous and Mesoporous Materials, 38: 3-24. https://doi.org/10.1016/S1387-1811(99)00295-4

Casado-Coterillo C., Fernández-Barquín, A., Zornoza, B., Téllez, C., and ÁngelIrabien, J.C., 2015. Synthesis and characterisation of MOF/ionic liquid/chitosan mixed matrix membranes for CO2/N2 separation. RSC Advances, 5(124): 102350-102361. https://doi.org/10.1039/C5RA19331A

Castarlenas, S., Téllez, C. and Coronas, J., 2017. Gas separation with mixed matrix membranes obtained from MOF UiO-66-graphite oxide hybrids. Journal of Membrane Science, 526(March): 205-211. https://doi.org/10.1016/j.memsci.2016.12.041

Castro-Muñoz, R., Fíla, V., Martin-Gil, V. and Muller, C., 2019. Enhanced CO2 permeability in Matrimid® 5218 mixed matrix membranes for separating binary CO2/CH4 mixtures. Separation and Purification Technology, 210: 553-562. https://doi.org/10.1016/j.seppur.2018.08.046

Castruita-de León, G., Yeverino-Miranda, C.Y., Montes-Luna, A. ge J., Meléndez-Ortiz, H.I., Alvarado-Tenorio, G. and García-Cerda, L.A., 2020. Amine-Impregnated natural zeolite as filler in mixed matrix membranes for CO2/CH4 separation. Applied Polymer Science, 137(3): 48286. https://doi.org/10.1002/app.48286

Chaidou, C.I., Pantoleontos, G., Koutsonikolas, D.E., Kaldis S.P. and Sakellaropoulos, G.P., 2012. Gas Separation Properties of Polyimide-Zeolite Mixed Matrix Membranes. Separation Science and Technology, 47(7): 950-962. https://doi.org/10.1080/01496395.2011.645263

Chen J.-T., Shih, C.-C., Fu Y.-J., Huang, S.-H., Hu, C.-C., Lee K.-R. and Lai, J.-Y., 2014. Zeolite-filled porous mixed-matrix membranes for air separation. Industrial Engineering and Chemistry Research, 53(7): 2781-2789. https://doi.org/10.1021/ie403833u

Chen, X.Y., Vinh-Thang, H., Ramirez, A.A., Rodrigue, D. and Kaliaguine, S., 2015. Membrane gas separation technologies for biogas upgrading. RSC Advances, 5(32): 24399-24448. https://doi.org/10.1039/C5RA00666J

Cheng, X., Zhang, A., Hou, K., Liu, M., Wang, Y., Song, C., Zhang, G. and Guo, X., 2013. Size-and morphology-controlled NH2-MIL- 53(Al) prepared in DMF − water mixed solvents. Dalton Transactions. 42(37): 13698-3705. https://doi.org/10.1039/c3dt51322j

Chung, T.S., Jiang, L.Y., Li, Y. and Kulprathipanja, S., 2007. Mixed matrix membranes (MMMs) comprising organic polymers with dispersed inorganic fillers for gas separation. Progress in Polymer Science, 32: 483-507. https://doi.org/10.1016/j.progpolymsci.2007.01.008

Dong, G., Li, H. and Chen, V., 2013. Challenges and opportunities for mixed-matrix membranes for gas separation. Journal of Materials Chemistry A, 1(15): 4610-4630. https://doi.org/10.1039/c3ta00927k

Dorosti, F. and Alizadehdakhel, A., 2018. Fabrication and investigation of PEBAX/Fe-BTC, a high permeable and CO2 selective mixed matrix membrane. Chemical Engineering Research and Design, 136(August): 119-128. https://doi.org/10.1016/j.cherd.2018.01.029

Dorosti, F., Omidkhah, M. and Abedini, R., 2014. Fabrication and characterization of Matrimid/MIL-53 mixed matrix membranefor CO2/CH4 separation. Chemical Engineering Research and Design, 92(11): 2439-2448. https://doi.org/10.1016/j.cherd.2014.02.018

Emovon, I. and Mgbemena, C.O., 2018. Machinery/Service system scheduled replacement time determination: A combine weighted aggregated sum product assessment, additive ratio assessment and age replacement model approach. International Journal of Integrated Engineering, 10: 169-175. https://doi.org/10.30880/ijie.2018.10.01.016

Emovon, I. and Samuel, O.D., 2017. Prioritising alternative solutions to power generation problems using MCDM techniques: Nigeria as case study. International Journal of Integrated Engineering, 9(3): 11-17.

Etxeberria-Benavides, M., David, O., Johnson, T., Łozińska, M.M., Orsi, A., Wright, P.A., Mastel, S., Hillenbrand, R. and Kapteijn, F., 2018. Gascon. High performance mixed matrix membranes (MMMs) composed of ZIF-94 filler and 6FDA-DAM polymer. Journal of Membrane Science, 550(March): 198-207. https://doi.org/10.1016/j.memsci.2017.12.033

Fang, M., Wu, C., Yang, Z., Wang, T., Xia, Y. and Li, J., 2015. ZIF-8/PDMS mixed matrix membranes for propane/nitrogen mixture separation: experimental result and permeation model validation. Journal of Membrane Science, 474(January): 103-113. https://doi.org/10.1016/j.memsci.2014.09.040

Feijani, E.A., Mahdavi, H. and Tavasoli, A., 2015. Poly (vinylidene fluoride) based mixed matrix membranes comprising metal organic frameworks for gas separation applications. Chemical Engineering Research and Design, 96(April): 87-102. https://doi.org/10.1016/j.cherd.2015.02.009

Feijani, E.A., Mahdavi, H. and Tavassoli, A., 2018. Synthesis and gas permselectivity of CuBTC-GO-PVDF mixed matrix membranes. New Journal of Chemistry, 42(14): 12013-12023. https://doi.org/10.1039/C8NJ00796A

Ferrey, G. and Serre, C., 2009. Large breathing effects in three-dimentional porous hybrid matter: Facts, analyses, rules and consequences. Chemical Society Reviews, 38(5): 1380-1399. https://doi.org/10.1039/b804302g

Friebe, S., Mundstock, A., Unruh, D., Renz, F. and Caro, J., 2016. NH2-MIL-125 as membrane for carbon dioxide sequestration: Thin supported MOF layers contra mixed-matrix-membranes. Journal of Membrane Science, 516(October): 185-193. https://doi.org/10.1016/j.memsci.2016.06.015

Funk, C.V. and Lloyd, D.R., 2008. Zeolite-filled microporous mixed matrix (ZeoTIPS) membranes: Prediction of gas separation performance. Journal of Membrane Science, 313(1-2): 224-231. https://doi.org/10.1016/j.memsci.2008.01.002

Gantzel, P.K. and Merten, U., 1970. Gas separations with high-flux cellulose acetate membranes. Industrial and Engineering Chemistry Process Design and Development, 9(2): 331-332. https://doi.org/10.1021/i260034a028

Gao, X., Zhang, J., Huang, K. and Zhang, J., 2018. ROMP for metal-organic frameworks: An efficient technique towards robust and high-separation performance membranes. ACS Applied Materials and Interfaces, 10(40): 34640−34645. https://doi.org/10.1021/acsami.8b12556

Gholami, M., Mohammadi, T., Mosleh, S. and Hemmati, M., 2017. CO2/CH4 separation using mixed matrix membrane-based polyurethane incorporated with ZIF-8 nanoparticles. Chemical Papers, 71(10): 1839-1853. https://doi.org/10.1007/s11696-017-0177-9

Goh, P.S., Ismail, A.F., Sanip, S.M., Ng, B.C. and Aziz, M., 2011. Recent advances of inorganic fillers in mixed matrix membrane for gas separation. Separation and Purification Technology, 81: 243-264. https://doi.org/10.1016/j.seppur.2011.07.042

Goncharenko, A.V., 2003. Generalizations of the Bruggeman equation and a concept of shape distributed particle composites. Physical Review, 68(4): 041108. https://doi.org/10.1103/PhysRevE.68.041108

Gorgojo, P., Sieffert, D., Staudt, C., Tellez, C. and Coronas, J., 2012. Exfoliated zeolite Nu-6 (2) as filler for 6FDA-based copolyimide mixed matrix membranes. Journal of Membrane Science, 411(September): 146-152. https://doi.org/10.1016/j.memsci.2012.04.025

Hafeez, S., Fan X., Hussain A. and Martín C.F., 2015. CO2 adsorption using TiO2 composite polymeric membranes: A kinetic study. Journal of Environmental Science, 35(September):163-171. https://doi.org/10.1016/j.jes.2015.04.019

He, X., Chu, Y., Lindbrathen, A., Hillestad, M. and Hagg, M.B., 2018. Carbon molecular sieve membranes for biogas upgrading: techno-economic feasibility analysis. Journal of Clean Products, 194: 584-593. https://doi.org/10.1016/j.jclepro.2018.05.172

Heidari, M., Hosseini, S.S, Nasrin, M.R.O. and Ghadimi, A., 2019. Synthesis and fabrication of adsorptive carbon nanoparticles (ACNs)/PDMS mixed matrix membranes for efficient CO2/CH4 and C3H8/CH4 separation. Separation and Purification Technology, 209(January): 503-515. https://doi.org/10.1016/j.seppur.2018.07.055

Hepburn, C., 2012. Property structure relationships in polyurethanes. In: Polyurethane Elastomers. Springer Science and Business Media. Second edition.

Herron, N., 1986. A cobalt oxygen carrier in zeolite Y: A molecular “ship in a bottle. Inorganic Chemistry, 25(26): 4714-4717. https://doi.org/10.1021/ic00246a025

Hou, J., Luan, Y., Huang, X., Gao, H., Yang M. and Lu, Y., 2017. Facile synthesis of Cu3(BTC)2/cellulose acetate mixed matrix membranes and their catalytic applications in continuous flow process. New Journal of Chemistry, 41(17): 9123-9129. https://doi.org/10.1039/C7NJ00672A

Hu, X., Lee, W.H., Bae, Y.J., Kim, J.S., Jung, J.T., Wang, H.H., Park, H.J. and Lee, Y.M., 2020. Thermally rearranged polybenzoxazole copolymers incorporating Tröger’s base for high flux gas separation membranes. Journal of Membrane Science, 612(October 2020): 118437. https://doi.org/10.1016/j.memsci.2020.118437

Hu, Y., Liu, Z., Xu, J., Huang Y. and Song, Y., 2013. Evidence of pressure enhanced CO2 storage in ZIF-8 probed by FTIR spectroscopy. Journal of American Chemical Society, 135(25): 9287-9290. https://doi.org/10.1021/ja403635b

Hu, Z., Kang, Z., Qian, Y., Peng, Y., Wang, X., Chi, C. and Zhao, D., 2016a. Mixed matrix membranes containing UiO-66(Hf)-(OH)2 metal-organic framework nanoparticles for efficient H2/CO2 separation. Industrial Engineering and Chemistry Research, 55(29): 7933-7940. https://doi.org/10.1021/acs.iecr.5b04568

Hu, Z.G., Nalaparaju, A., Peng, Y.W., Jiang, J.W. and Zhao, D., 2016b. Modulated hydrothermal synthesis of UiO-66(Hf)-type metal-organic frameworks for optimal carbon dioxide separation. Inorganic Chemistry, 55(3): 1134-1141. https://doi.org/10.1021/acs.inorgchem.5b02312

Hua, Y., Wang, H., Li, Q., Chen, G., Liu, G., Duan, J. and Jin. W., 2018. Highly efficient CH4 purification by LaBTB PCP-based mixed matrix membranes. Journal of Materials Chemistry A, 6: 599-606. https://doi.org/10.1039/C7TA07261A

Isfahani, A.P., Ghalei, B. and Bagheri, R., 2016a. Polyurethane gas separation membranes with ethereal bonds in the hard segments. Journal of Membrane Science, 513(September): 58-66. https://doi.org/10.1016/j.memsci.2016.04.030

Isfahani, A.P., Sadeghi, M., Dehaghani, A.H.S. and Aravand, M.A., 2016b. Enhancement of the gas separation properties of polyurethane membrane by epoxy nanoparticles. Journal of Industrial and Engineering Chemistry, 44(25): 67-72. https://doi.org/10.1016/j.jiec.2016.08.012

Ishaq, S., Tamime, R., Bilad, M.R. and Khan, A.L., 2019. Mixed matrix membranes comprising of Polysulfone and Microporous BIOMOF-1: Preparation and Gas Separation Properties. Separation and Purification Technology, 210(February): 442-451. https://doi.org/10.1016/j.seppur.2018.08.031

Ismail, A.F., Kusworo, T.D. and Mustafa, A., 2008. Enhanced gas permeation performance of polyethersulfone mixed matrix hollow fiber membranes using novel Dynasylan Ameosilane agent. Journal of Membrane Science, 319(1-2): 306-312. https://doi.org/10.1016/j.memsci.2008.03.067

Ismail, A.F., Rahim, N.H., Mustafa, A., Matsuura, T., Ng, B.C., Abdullah, S. and Hashemifard, S.A., 2011. Gas separation performance of polyethersulfone/multi-walled carbon nano tubes mixed matrix membranes. Separation and Purification Technology, 80(1): 20-31. https://doi.org/10.1016/j.seppur.2011.03.031

Jeazet, H.B.T., Sorribas, S. and Román-Marín, J.M., 2016. Increased selectivity in CO2/CH4 separation with mixed matrix membranes of polysulfone and mixed-MOFs MIL-101(Cr) and ZIF-8. European Journal of Inorganic Chemistry, 2016(27): 4363-4367. https://doi.org/10.1002/ejic.201600190

Jeon, Y.-W. and Shin, M.-S., 2017. Separation of biogas using newly prepared cellulose acetate hollow fiber membranes. Conference on energy and environment research, ICEER 2017, 17-20 July, 2017, Porto, Portogal, Energy Procedia, 136(October): 219-224. https://doi.org/10.1016/j.egypro.2017.10.243

Jeong, H.K., Krych, W., Ramanan, H., Nair, S., Marand, E. and Tsapatsis, M., 2004. Fabrication of polymer/selective-flake nanocomposite membranes and their use in gas separation. Chemistry of Materials. 16(20): 3838-3845. https://doi.org/10.1021/cm049154u

Jeong, H.K., Nair, S., Vogt, T., Dickinson, L.C. and Tsapatsis, M., 2003. A highly crystalline layered silicate with three-dimensionally microporous layers. Nature Materials, 2: 53-58. https://doi.org/10.1038/nmat795

Jian, Y., Yin, H., Chang, F., Yang, J., Mu, W., Li. X., Lu, J., Zhang, Y. and Wang, J., 2017. Facile synthesis of highly permeable CAU-1 tubular membranes for separation of CO2/N2 mixtures. Journal of Membrane Science, 522(January): 140-150. https://doi.org/10.1016/j.memsci.2016.08.060

Jusoh, N., Yeong, Y.F., Lau, K.K. and Shariff, A.M., 2017a. Enhanced gas separation performance using mixed matrix membranes containing zeolite T and 6FDA-durene polyimide. Journal of Membrane Science, 525(March): 175-186. https://doi.org/10.1016/j.memsci.2016.10.044

Jusoh, N., Yeong, Y.F., Lau, K.K. and Shariff, A.M., 2017b. Fabrication of 6FDA-durene membrane incorporated with zeolite T and aminosilane grafted zeolite T for CO2/CH4 separation. IOP Conference Series: Materials Science and Engineering, 226: 012169. https://doi.org/10.1088/1757-899X/226/1/012169

Jusoh, N., Yeong, Y.F., Lau, K.K. and Shariff, A.M., 2018. Effects of amine-functionalization on mixed matrix membranes encompassing of T-Type zeolite and 6FDA-based polyimide for separation of CO2 from CH4. International Journal of Automotive and Mechanical Engineering, 15(1): 5126-5134. https://doi.org/10.15282/ijame.15.1.2018.17.0396

Kaeselev, B., Pieracci, J. and Belfort, G., 2001. Photoinduced grafting of ultrafiltration membranes: Comparison of poly (ether sulfone) and poly (sulfone). Journal of Membrane Science, 194(2): 245-261. https://doi.org/10.1016/S0376-7388(01)00544-0

Kahlen, W., Wagner, H.H. and Holderich, W.F., 1998. Zeolite effect in the enantioselective transhydrogenation over a Co-salen “ship-in-the-bottle” complex. Catalysis Letters, 54(1-2): 85-89. https://doi.org/10.1023/A:1019027921973

Kertik, A., Wee, L.H., Pfannmöller, Bals, S., Martens, J.A. and Vankelecom, I.F.J., 2017. Highly selective gas separation membrane using in-situ amorphised metal-organic frameworks. Energy and Environmental Science, 10(11): 2342-2351. https://doi.org/10.1039/C7EE01872J

Khan, A.L., Klaysom, C., Gahlaut, A. and Vankelecom, I.F.J., 2013b. Polysulfone acrylate membranes containing functionalized mesoporous MCM-41 for CO2 separation. Journal of Membrane Science, 436(June): 145-153. https://doi.org/10.1016/j.memsci.2013.02.023

Khan, A.L., Klaysom, C., Gahlaut, A., Khan, A.U. and Vankelecom, I.F.J., 2013a. Mixed matrix membranes comprising of Matrimid and -SO3H functionalized mesoporous MCM-41for gas separation. Journal of Membrane Science, 447(November): 73-79. https://doi.org/10.1016/j.memsci.2013.07.011

Khan, A.L., Li, X. and Vankelecom, I.F.J., 2011. SPEEK/Matrimid blend membranes for CO2 separation. Journal of Membrane Science, 380(1-2): 55-62. https://doi.org/10.1016/j.memsci.2011.06.030

Khan, A.L., Sree, S.P. and Martens, J.A., 2015. Mixed matrix membranes comprising of matrimid and mesoporous COK-12: Preparation and gas separation properties. Journal of Membrane Science, 495(December): 471-478. https://doi.org/10.1016/j.memsci.2015.08.008

Khdhayyer, M., Bushell, A.F., Budd, P.M., Attfield, M.P., Jiang, D., Burrows, A.D., Esposito, E., Bernardo, P., Monteleone, M., Fuoco, A., Clarizia, G., Bazzarelli, F., Gordano, A. and Jansen, J.C., 2019. Mixed matrix membranes based on MIL-101 metal-organic frameworks in polymer of intrinsic microporosity. Separation and Purification Technology, 212(April): 545-554. https://doi.org/10.1016/j.seppur.2018.11.055

Kilduff, J.E., Mattaraj, S., Pieracci, J.P. and Belfort, G., 2000. Photochemical modification of poly (ether sulfone) and sulfonated (polysulfone) nanofiltration membranes for control of fouling of natural organic matter. Desalination, 132(1): 133-142. https://doi.org/10.1016/S0011-9164(00)00142-9

Kim, C.R., Uemura, T. and Kitagawa, S., 2016a. Inorganic nanoparticles in porous coordination polymers. Chemical Society Reviews, 45(14): 3828−3845. https://doi.org/10.1039/C5CS00940E

Kim, J., Choi, J., Kang, Y.S. and Won, J., 2016b. Matrix effect of mixed-matrix membrane containing CO2-selective MOFs. Journal of Applied Polymer Science, 133(1): 42853-42856. https://doi.org/10.1002/app.42853

Kim, J., Kim, W.Y. and Ahn, W.-S. 2012a. Amine-functionalized MIL-53(Al) for CO2/N2 separation: Effect of textural properties. Fuel, 102(December): 574-579. https://doi.org/10.1016/j.fuel.2012.06.016

Kim, S. and Marand, E., 2008. High permeability nano-composite membranes based on mesoporous MCM-41 nanoparticles in a polysulfone matrix. Microporous and Mesoporous Materials, 114(1-3): 129-136. https://doi.org/10.1016/j.micromeso.2007.12.028

Kim, S., Marand, E., Ida, J. and Guliants, V.V., 2006b. Polysulfone and mesoporous molecular sieve MCM-48 mixed matrix membranes for gas separation. Chemistry of Materials, 18(5): 1149-1155. https://doi.org/10.1021/cm052305o

Kim, S., Pechar, T.W. and Marand, E., 2006a. Poly(imidesiloxane) and carbon nanotube Mixed matrix membranes for gas separation. Desalination, 192(1-3): 330-339. https://doi.org/10.1016/j.desal.2005.03.098

Kim, T., Choi, M.-k., Ahn, H.S., Rho, J., Jeong M.H. and Kim, K., 2019. Fabrication and characterization of zeolitic imidazolate framework embedded cellulose acetate membranes for osmotically driven membrane process. Scientific Reports, 9, Article number.5779. https://doi.org/10.1038/s41598-019-42235-5

Kim, W.-g., Lee, J.S. and Bucknall, D.G., 2013. Nanoporous layered silicate AMH-3/cellulose acetate nanocomposite membranes for gas separations. Journal of Membrane Science, 441(April): 129-136. https://doi.org/10.1016/j.memsci.2013.03.044

Kim, W.-G., Zhang, X., Lee, J.S., Tsapatsis, M. and Nair, S., 2012b. Epitaxially grown layered MFI-Bulk MFI Hybrid Zeolitic materials. ASC Nano, 6(11): 9978-9988. https://doi.org/10.1021/nn3036254

Kubica, P., Wolinska-Grabczyk, A., Grabiec, E., Libera, M., Wojtyniak, M., Czajkowska, S. and Domański, M., 2016. Gas transport through mixed matrix membranes composed of polysulfone and copper terephthalate particles. Microporous and Mesoporous Materials, 235(November): 120-134. https://doi.org/10.1016/j.micromeso.2016.07.037

Kulprathipanja, S., Neuzil, R.W. and Li, N.N., 1988. Separation of fluids by means of mixed matrix membranes, US. Patent, pp. 4740219.

Lewis, T. and Nielsen, L.E., 1970. Dynamic mechanical properties of particulate-filled composites. Journal of Applied Polymer Science, 14(6): 1449-1471. https://doi.org/10.1002/app.1970.070140604

Li, K., Olson, D.H., Seidel, J., Emge, T.J., Gong, H., Zeng, H. and Li, J., 2009. Zeolitic imidazolate frameworks for kinetic separation of propane and propene. Journal of American Chemical Society, 131(30): 10368-10369. https://doi.org/10.1021/ja9039983

Li, S., Falconer, J.L. and Noble, R.D., 2006b. Improved SAPO-34 membranes for CO2/CH4 separations. Advanced Materials, 18(19): 2601-2603. https://doi.org/10.1002/adma.200601147

Li, T., Pan, Y., Peinemann, K.-V. and Lai, Z., 2013a. Carbon dioxide selective mixed matrix composite membrane containing ZIF-7 nano-fillers. Journal of Membrane Science, 425-426: 235-242. https://doi.org/10.1016/j.memsci.2012.09.006

Li, W., Pan, F., Song, Y., Wang, M., Wang, H., Walker, S. and Jiang, Z., 2017. Construction of molecule-selective mixed matrix membranes with confined mass transfer structure. Chinese Journal of Chemical Engineering, 25: 1563-1580. https://doi.org/10.1016/j.cjche.2017.04.015

Li, Y., Chung, T.S., Huang, Z. and Kulprathipanja, S., 2006a. Dual-layer polyethersulfone (PES)/BTDA-TDI/MDI co-polyimide (P84) hollow fiber membranes with a submicron PES-zeolite beta mixed matrix dense-selective layer for gas separation. Journal of Membrane Science, 277(1): 28-37. https://doi.org/10.1016/j.memsci.2005.10.008

Li, Y., He, G. Wang, S., Yu, S. Pan, F., Wu, H. and Jiang, Z., 2013b. Recent advances in the fabrication of advanced composite membranes. Journal of Materials Chemistry A, 1(35): 10058-10077. https://doi.org/10.1039/c3ta01652h

Liaw, D.-J., Wang, K.-L., Huang, Y.-C., Lee, K.-R., Lai, J.-Y. and Ha, C.-S. 2012. Advanced polyimide materials: Syntheses, physical properties and applications. Progress in Polymer Science, 37(7): 907-974. https://doi.org/10.1016/j.progpolymsci.2012.02.005

Lin, H.Q. and Freeman, B.D., 2005. Materials selection guidelines for membranes that remove CO2 from gas mixtures. Journal of Molecular Structure, 739 (1-3): 57-74. https://doi.org/10.1016/j.molstruc.2004.07.045

Liu, C., Kulprathipanja, S., Hillock, A.M.W., Husain, S. and Koros, W.J., 2008. N.N. Li, A.G. Fane, W.S. Winston Hov and T. Matsuura (eds), Advanced membrane technology and applications. Part IV. Membrane materials and characterization. Recent Progress in Mixed-Matrix Membranes. pp. 789-819. John Wiley and Sons Ltd., Hoboken, New Jersey.

Liu, L., Chakma, A. and Feng, X., 2004. Preparation of hollow fiber poly (ether block amide)/ polysulfone composite membranes for separation of carbon dioxide from nitrogen. Chemical Engineering Journal, 105(1-2): 43-51. https://doi.org/10.1016/j.cej.2004.08.005

Liu, T., Tong, Y. and Zhang, W.-D., 2007. Preparation and characterization of carbon nanotube/polyetherimide nanocomposite films. Composite Science and Technology, 67(3-4): 406-412. https://doi.org/10.1016/j.compscitech.2006.09.007

Lydon, M.E, Unocic, K.A., Bae, T.-H., Jones, C.W. and Nair, S., 2012. Structure-property relationships of Inorganically-surface modified zeolite molecular sieves for nanocomposite membrane fabrication. Journal of Physical Chemistry C, 116(17): 9636-9645. https://doi.org/10.1021/jp301497d

Mahajan, R. and Koros, W.J., 2000. Factors controlling successful formation of mixed-matrix gas separation materials. Industrial and Engineering Chemistry Research, 39(8): 2692–2696. https://doi.org/10.1021/ie990799r

Marian, H., Orluk, P., Zakrzewska-Trznadel, G. and Chmielewski, A.G., 2007. Application of polyimide membranes for biogas purification and enrichment. Journal of Hazardous Materials, 144(3): 698-702. https://doi.org/10.1016/j.jhazmat.2007.01.098

Marti, A., Venna, S., Roth, E.A., Culp, J.T. and Hopkinson, D.P., 2018. A simple fabrication method for mixed matrix membranes with in-situ MOF growth for gas separation. ACS Applied Materials and Interfaces. 10: 24784-24790. https://doi.org/10.1021/acsami.8b06592

Mathews, A.S., Kim, I. and Ha, C.-S. 2007. Synthesis, characterization, and properties of fully aliphatic polyimides and their derivatives for microelectronics and optoelectronics applications. Macromolecular Research, 15 (2): 114-128. https://doi.org/10.1007/BF03218762

Meshkat, S., Kaliaguine, S. and Rodrigue, D., 2018. Mixed matrix membranes based on amine and non-amine MIL-53(Al) in Pebax® MH-1657 for CO2 separation. Separation and Purification Technology, 200: 177-190. https://doi.org/10.1016/j.seppur.2018.02.038

Miller, J.K. and Miller, S.J., 2003. Effect of condensable impurities in CO2/CH4 gas feeds on carbon molecular sieve hollow-fiber membranes. Industrial and Engineering Chemistry Research, 42(5): 1064-1075. https://doi.org/10.1021/ie020698k

Moghadassi, A.R., Rajabi, Z., Hosseini, S.M. and Mohammadi, M., 2014. Fabrication and modification of cellulose acetate based mixed matrix membrane: Gas separation and physical properties. Journal of Industrial and Engineering Chemistry, 20(May): 1050-1060. https://doi.org/10.1016/j.jiec.2013.06.042

Mubashir, M., Fong, Y.Y, and Lau, K.K., 2016. Ultrasonic-assisted secondary growth of decadodecasil3 rhombohedral (DD3R) membrane and its process optimization studies in CO2/CH4 separation using response surface methodology. Journal of Natural Gas Science and Engineering, 30: 50-63. https://doi.org/10.1016/j.jngse.2016.01.015

Mubashir, M., Fong, Y.Y., Leng, C.T. and Keong L.K., 2018a. Enhanced gases separation of cellulose acetate membrane using N-Methyl-1-2 pyrrolidone as fabrication solvent. International Journal of Automotive and Mechanical Engineering, 15(1): 4978-4986. https://doi.org/10.15282/ijame.15.1.2018.7.0386

Mubashir, M., Fong, Y.Y., Thiam-Leng, C., and Keong, L.K., 2018c. Prediction of CO2 permeability in NH2-MIL 53(Al)/cellulose acetate mixed matrix membranes using theoretical models. International Journal of Integrated Engineering, Special issue 2018, Mechenical Engineering, 10(5): 176-180. https://doi.org/10.30880/ijie.2018.10.05.026

Mubashir, M., Yeong, Y.F., Chew, T.L. and Lau, K.K., 2019. Comparison of post-treatment methods on the performance of hollow fiber membranes containing metal organic framework in gases separation. Industrial and Engineering Chemistry Research, 58(17): 7120-7130. https://doi.org/10.1021/acs.iecr.8b05773

Mubashir, M., Yeong, Y.F., Lau, K.K. and Jusoh, N., 2018b. Efficient CO2/N2 and CO2/CH4 separation by using NH2-MIL-53(Al)/cellulose acetate (CA) mixed matrix membranes. Separation and Purification Technology, 199(June): 140-151. https://doi.org/10.1016/j.seppur.2018.01.038

Muhammad, M., Yeong, Y.F., Lau, K.K. and Mohd, S.A.B., 2015. Issues and challenges in the development of Deca-Dodecasil 3 Rhombohedral membrane in CO2 capture from natural gas. Separation and Purification Reviews, 44(4): 331-340. https://doi.org/10.1080/15422119.2014.970195

Murali, R.S., Ismail, A.F., Rahman, M.A. and Sridhar, S., 2014. Mixed matrix membranes of Pebax-1657 loaded with 4A zeolite for gaseous separations. Separation and Purification Technology, 129(May): 1-8. https://doi.org/10.1016/j.seppur.2014.03.017

Najafi, M., Sadeghi, M., Bolverdi, A., Chenar, P.M. and Pakizeh, M., 2018. Gas permeation properties of cellulose acetate/silica nano composite membrane. Advances in Polymer Technology, 37(6): 2043-2052. https://doi.org/10.1002/adv.21862

Neoh, T.-L., Yoshii, H., and Furuta, T., 2006. Encapsulation and release characteristics of carbon dioxidein α-cyclodextrin. Journal of Inclusion Phenomena and Macrocyclic Chemistry, 56(1-2): 125-133. https://doi.org/10.1007/s10847-006-9073-6

Nik, O.G., Chen, X.Y. and Kaliaguine, S., 2012. Functionalized metal organic framework-polyimide mixed matrix membranes for CO2/CH4 separation. Journal of Membrane Science, 413–414; (September): 48-61. https://doi.org/10.1016/j.memsci.2012.04.003

Nordin, N.A.H.M., Ismail, A.F., Mustafa, A., Murali, R.S. and Matsuura, T., 2015. Utilizing low ZIF-8 loading for an asymmetric PSf/ZIF-8 mixed matrix membrane for CO2/CH4 separation. RSC Advances, 5(38): 30206-30215. https://doi.org/10.1039/C5RA00567A

Ozen, H.A. and Ozturk, B., 2019. Gas separation characteristic of mixed matrix membrane prepared by MOF-5 including different metals. Separation and Purification Technology, 211(March): 514-521. https://doi.org/10.1016/j.seppur.2018.09.052

Pal, R., 2007. New models for thermal conductivity of particulate composites. Journal of Reinforced Plastics and Composites, 26(7): 643-651. https://doi.org/10.1177/0731684407075569

Pang, H., Gong, H., Du, M., Shen, Q. and Chen, Z., 2018. Effect of non-solvent additive concentration on CO2 absorption performance of polyvinylidene fluoride hollow fiber membrane contactor. Separation and Purification Technology, 191(January): 38-37. https://doi.org/10.1016/j.seppur.2017.09.012

Perea-Cachero, A., Sánchez-Laínez, J., Zornoza, B., Romero-Pascual, E., Téllez, C. and Coronasa, J., 2019. Nanosheets of MIL-53(Al) applied in membranes with improved CO2/N2 and CO2/CH4 selectivities. Dalton Transactions, 48(10): 3392-3403. https://doi.org/10.1039/C8DT03774D

Phan, A., Doonan, C.J. and Uribe-Romo, F.J., 2010. Synthesis, structure, and carbon dioxide capture properties of zeolitic imidazolate frameworks. Accounts of Chemical Research, 43(1): 58-67. https://doi.org/10.1021/ar900116g

Ploegmakers, J., Japip, S. and Nijmeijer, K., 2013. Mixed matrix membranes containing MOFs for ethylene/ethane separation-Part B: effect of Cu3BTC2 on membrane transport properties. Journal of Membrane Science, 428(February): 331-340. https://doi.org/10.1016/j.memsci.2012.11.013

Pratibha, P. and Chauhan, R.S., 2001. Membranes for gas separation. Progress in Polymer Science, 26(6): 853-893. https://doi.org/10.1016/S0079-6700(01)00009-0

Raymond, P.C., Koros, W.J. and Paul, D.R., 1993. Comparison of mixed and pure gas permeation characteristics for CO2 and CH4 in copolymers and blends containing methyl methacrylate units. Journal of Membrane Science, 77(1): 49-57. https://doi.org/10.1016/0376-7388(93)85234-N

Rehman, A., Farrukh, S., Hussain, A. and Pervaiz, E., 2020. Synthesis and effect of metal–organic frame works on CO2 adsorption capacity at various pressures: A contemplating review. Energy and Environment, 31(3): 367-388. https://doi.org/10.1177/0958305X19865352

Reid, B.D., Ruiz-Trevino, F.A., Musselman, I.H., Balkus, K.J. and Ferraris, J.P., 2001. Gas permeability properties of polysulfone membranes containing the mesoporous molecular sieve MCM-41. Chemistry of Materials, 13(7): 2366-2373. https://doi.org/10.1021/cm000931+

Reijerkerk, S.R., Knoef, M.H., Nijmeijer, K. and Wessling, M., 2010. Poly (ethylene glycol) and poly (dimethyl siloxane): Combining their advantages into efficient CO2 gas separation membranes. Journal of Membrane Science, 352(1-2): 126-135. https://doi.org/10.1016/j.memsci.2010.02.008

Rezakazemi, M, Amooghin, A.E. and Montazer-Rahmati, M.M., 2014. State-of-the-art membrane based CO2 separation using mixed matrix membranes (MMMs): An overview on current status and future directions. Progress in Polymer Science, 39(5): 817-861. https://doi.org/10.1016/j.progpolymsci.2014.01.003

Rezakazemi, M., Sadrzadeh, M. and Matsuura, T., 2018. Thermally stable polymers for advanced high-performance gas separation membranes. Progress in Energy and Combustion Science, 66: 1-41. https://doi.org/10.1016/j.pecs.2017.11.002

Rodenas, T., van Dalen, M., García-Pérez, E., Serra-Crespo, P., Zornoza, B., Kapteijn, F. and Gascon, J., 2014. Visualizing MOF mixed matrix membranes at the nanoscale: Towards structure-performance relationships in CO2/CH4 separation over NH2-MIL-53(Al)@PI. Advanced Functional Materials, 24(2): 249-256. 2013 WILEY-VCH Verlag GmbH andCo. KGaA, Weinheim. https://doi.org/10.1002/adfm.201203462

Roth, W.J. and Cejka, J., 2011. Two-dimensional zeolites: dreamorreality? Catalysis Science and Technology, 1: 43-53. https://doi.org/10.1039/c0cy00027b

Rubio, C., Casado, C., Gorgojo, P., Etayo, F., Uriel, S., Tellez, C. and Coronas, J., 2010. Exfoliated titanosilicate material UZAR-S1 obtained from JDF-L1. European Journal of Inorganic Chemistry, 2010(1): 159-163. https://doi.org/10.1002/ejic.200900915

Sakamoto, Y., Nagata, K., Yogo, K. and Yamada, K., 2007. High permeability nano-composite membranes based on mesoporous MCM-41 nanoparticles in a polysulfone matrix. Microporous and Mesoporous Materials, 101(1-2): 303-311. https://doi.org/10.1016/j.micromeso.2006.11.007

Sanaeepur, H., Amooghin, A.E., Kargari, A., Omidkhah, M., Ismail, A.F. and Ramakrishna, S., 2019. Interior modification of nano-porous fillers to fabricate high-performance mixed matrix membranes. Journal of Chemical Engineering, 16(2): (Spring 2019), IAChE.

Sanaeepur, H., Kargari, A. and Nasernejad, B., 2014. Aminosilane functionalization of a nanoporous Y-type zeolite for application in a cellulose acetate based mixed matrix membrane for CO2 separation. RSC Advances, 4(109): 63966-63976. https://doi.org/10.1039/C4RA08783F

Sanaeepur, H., Nasernejad, B. and Kargari, A., 2015. Cellulose acetate/nano-porous zeolite mixed matrix membrane for CO2 separation. Greenhouse Gases Science and Technology, 5(3): 291-304. https://doi.org/10.1002/ghg.1478

Sanip, S., Ismail, A., and Ng, B., Abdullah, M., Soga, T., Tanemura, M. and Yasuhiko, H., 2010. Preparation and characteristics of functionalized multiwalled carbon nano-tubes in polyimide mixed matrix membrane, Nano: Brief Reports and Reviews, 5(4): 195-202. https://doi.org/10.1142/S1793292010002104

Sanip, S.M., Ismail, A.F., Goh, P.S., Soga, T., Tanemura, M. and Yasuhiko, H., 2011. Gas separation properties of functionalized carbon nanotubes mixed matrix membranes. Separation and Purification Technology, 78(2): 208-213. https://doi.org/10.1016/j.seppur.2011.02.003

Sarfraz, M. and Ba-Shammakh, M., 2016a. Synergistic effect of incorporating ZIF-302 and graphene oxide to polysulfone to develop highly selective mixed-matrix membranes for carbon dioxide separation from wet post-combustion flue gases. Journal of Industrial and Engineering Chemistry, 36(April): 154-162. https://doi.org/10.1016/j.jiec.2016.01.032

Sarfraz, M. and Ba-Shammakh, M., 2016b. Combined effect of CNTs with ZIF-302 into polysulfone to fabricate MMMs for enhanced CO2 separation from flue gases. Arabian Journal for Science and Engineering, 41: 2573-2582. https://doi.org/10.1007/s13369-016-2096-4

Scholes, C.A., Kentish, S.E. and Stevens, G.W., 2008. Carbon dioxide separation through polymeric membrane systems for flue gas applications. Recent Patents on Chemical Engineering, 1(1): 52-66. https://doi.org/10.2174/2211334710801010052

Şen, D., Kalıpçılar, H. and Yilmaz, L., 2007. Development of polycarbonate based zeolite 4A filled mixed matrix gas separation membranes. Journal of Membrane Science, 303(1-2): 194-203. https://doi.org/10.1016/j.memsci.2007.07.010

Shahid, S. and Nijmeijer, K., 2014. Performance and plasticization behavior of polymer-MOF membranes for gas separation at elevated pressures. Journal of Membrane Science, 470(November): 166-177. https://doi.org/10.1016/j.memsci.2014.07.034

Shen, J.N., Yu, C.C., Zeng, G.N. and Bruggen, B., 2013. Preparation of a facilitated transport membrane composed of carboxymethyl chitosan and polyethylenimine for CO2/N2 separation. International Journal of Molecular Science, 14(2): 3621-3638. https://doi.org/10.3390/ijms14023621

Shu, S., Husain, S. and Koros, W.J., 2007. A general strategy for adhesion enhancement in polymeric composites by formation of nanostructured particle surfaces. Journal of Physical Chemistry C, 111(2): 652-657. https://doi.org/10.1021/jp065711j

Si, X., Jiao. C., Li. F., Zhang, J., Wang, S., Liu, S., Li, Z., Sun, L., Xu, F., Gabelica, A. and Schick, C., 2011. High and selective CO2 uptake, H2 storage and methanol sensing on the amine-decorated 12-Connected MOF CAU-1. Energy and Environmental Science, 4(11): 4522-4527. https://doi.org/10.1039/c1ee01380g

Sijbesma, H., Nymeijer, K., and van Marwijk, R., 2008. Flue gas dehydration using polymer membranes. Journal of Membrane Science, 313(1-2): 263-276. https://doi.org/10.1016/j.memsci.2008.01.024

Song, Q., Nataraj, S.K., Roussenova, M.V., Tan, J.C., Hughes, D.J., Li, W., Bourgoin, P., Alam, M.A., Cheetham, A.K., Al-Muhtaseb, S.A. and Sivaniah, E., 2012. Zeolitic imidazolate framework (ZIF-8) based polymer nanocomposite membranes for gas separation. Energy and Environmental Science, 5: 8359-8369. https://doi.org/10.1039/c2ee21996d

Sun, J., Li, Q., Chen, G., Duan, J., Liu, G. and Jin, W., 2019. MOF-801 incorporated PEBA mixed-matrix composite membranes for CO2 capture. Separation and Purification Technology, 217(June): 229-239. https://doi.org/10.1016/j.seppur.2019.02.036

Sutrisna, P.D., Hou, J., Zulkifli, M.Y., Li, H., Zhang, Y., Liang, W., D’Alessandro, D.M. and Chen, V., 2018. Surface functionalized UiO-66/Pebax-based ultrathin composite hollow fiber gas separation membranes. Journal of Materials Chemistry A, 6(3): 918-931. https://doi.org/10.1039/C7TA07512J

Tahir, Z., Aslam, M., Gilani, M.A., Bilad, M.R., Anjum, M.W., Zhu, L.-P. and Khan, A.L., 2019. -SO3H functionalized UiO-66 nanocrystals in Polysulfone based mixed matrix membranes: Synthesis and application for efficient CO2 capture. Separation and Purification Technology, 224(October): 524-533. https://doi.org/10.1016/j.seppur.2019.05.060

Tahir, Z., Ilyas, A., Li, X., Bilad, M.R, Vankelecom, I.F. and Khan, A.L., 2018. Tuning the gas separation performance of fluorinated and sulfonated PEEK membranes by incorporation of zeolite 4A. Journal of Applied Polymer Science, 135(10): 45952-45960. https://doi.org/10.1002/app.45952

Tai-Shung, C., Kafchinski, E. and Vora, R., 1994. Development of a defect-free 6FDA-durene asymmetric hollow fiber and its composite hollow fibers. Journal of Membrane Science, 88(1): 21-36. https://doi.org/10.1016/0376-7388(93)E0163-E

Tariq, A.R., Tariq, S.R., Sultan, M., Mahmud, T. and Chotana, G.A., 2020. Selective CO2 capture through microporous Tb (BTC)(H2O). (DMF)1.1 MOF as an additive in novel MMMs fabricated from Matrimid® 5218. Arabian Journal of Chemistry, https://doi.org/10.1016/j.arabjc.2020.10.021

Tocci, E., Gugliuzza, A., De Lorenzo, L., Macchione, M., De Luca, G. and Drioli, E., 2008. Transport properties of a co-poly (amide-12-b-ethylene oxide) membrane: A comparative study between experimental and molecular modelling results. Journal of Membrane Science, 323(2): 316-327. https://doi.org/10.1016/j.memsci.2008.06.031

Trotta, F., Cavalli, R., Martina, K., Biasizzo, M., Vitillo, J., Bordiga, S., Vavia, P. and Ansari, K., 2011. Cyclodextrin nanosponges as effective gas carriers. Journal of Inclusion Phenomena and Macrocyclic Chemistry, 71(1-2): 189-194. https://doi.org/10.1007/s10847-011-9926-5

Tsai, H.A., Chen, Y.L., Huang, S.H., Hu, C.C., Hung, W.S., Lee, K.R. and Lai, J.Y., 2018. Preparation of polyamide/polyacrylonitrile composite hollow fiber membrane by synchronous procedure of spinning and interfacial polymerization. Journal of Membrane Science, 551(April): 261-272. https://doi.org/10.1016/j.memsci.2018.01.059

Venna, S.R., Lartey, M., Li, T., Spore, A., Kumar, S., Nulwala, H.B., Luebke, D.R., Rosi, N.L. and Albenze, E., 2015. Fabrication of MMMs with improved gas separation properties using externally-functionalized MOF particles. Journal of Materials Chemistry A, 3(9): 5014-5022. https://doi.org/10.1039/C4TA05225K

Wahab, M.F.A., Ismail, A.F. and Shilton, S.J., 2012. Issues and challenges in the Development of Deca-Dodecasil 3 Rhombohedral Membrane in CO2 capture from natural gas. Separation and Purification Technology, 86(February): 41-48. https://doi.org/10.1016/j.seppur.2011.10.018

Waheed, N., Mushtaq, A., Tabassum, S., Gilani, M.A., Ilyas, A., Ashraf, F., Jamal, Y., Bilad, M.R., Khan, A.U. and Khan, A.L., 2016. Matrix Membranes Based on polysulfone and rice husk extracted silica for CO2 separation. Separation and Purification Technology, 170(October): 122-129. https://doi.org/10.1016/j.seppur.2016.06.035

Wang, H., Zhang, K., Li, J.P.H., Huang, J., Yuan, B., Zhang, C., Yu, Y., Lee, Y. and Li, T., 2020. Engineering plasticization resistance gas separation membranes using metal-organic nanocapsules. Chemical Science, 11(18): 4687-4694. https://doi.org/10.1039/D0SC01498B

Ward, J.K. and Koros, W.J., 2011. Crosslinkable mixed matrix membranes with surface modified molecular sieves for natural gas purification: II. Performance characterization under contaminated feed conditions. Journal of Membrane Science, 377: 82-88. https://doi.org/10.1016/j.memsci.2011.04.015

Widjojo, N., Chung, T.S. and Kulprathipanja, S., 2008. The fabrication of hollow fiber membranes with double-layer mixed-matrix materials for gas separation. Journal of Membrane Science, 325(November): 326−335. https://doi.org/10.1016/j.memsci.2008.07.046

Wolińska-Grabczyk, A., Kubica, P., Jankowski, A., Wojtowicz, M., Kansy, J. and Wójtyniak, M., 2017. Gas and water vapor transport properties of mixed matrix membranes containing 13X zeolite. Journal of Membrane Science, 526: 334-347. https://doi.org/10.1016/j.memsci.2016.11.031

Wu, H., Li, X., Li, Y. Wang, S., Guo, R., Jiang, Z., Wu, C., Xin, Q. and Lu, X., 2014. Facilitated transport mixed matrix membranes incorporated with amine functionalized MCM-41forenhanced gas separation properties. Journal of Membrane Science, 465: 78-90. https://doi.org/10.1016/j.memsci.2014.04.023

Xiang, L., Pan, Y., Zeng, G., Jiang, J., Chen, J. and Wang, C., 2016. Preparation of poly (etherblock- amide)/attapulgite mixed matrix membranes for CO2/N2 separation. Journal of Membrane Science, 500(February): 66-75. https://doi.org/10.1016/j.memsci.2015.11.017

Xin, Q., Liu, T., Li, Z., Wang, S., Li, Y., Li, Z., Ouyang, J., Jiang, Z. and Wu, H., 2015. Mixed matrix membranes composed of sulfonated poly (ether ether ketone) and a sulfonated metal-organic framework for gas separation. Journal of Membrane Science, 488(August): 67-78. https://doi.org/10.1016/j.memsci.2015.03.060

Xin, Q., Wu, H., Jiang, Z., Li, Y., Wang, S., Li, Q., Li, X., Lu, X., Cao, X. and Yang, J., 2014. SPEEK/amine-functionalized TiO2 submicrospheres mixed matrix membranes for CO2 separation. Journal of Membrane Science, 467(October): 23-35. https://doi.org/10.1016/j.memsci.2014.04.048

Xiong, D.B., Zhao J.T., Chen, H.H. and Yang, X.X., 2007. A borogermanate with three-dimensional open-framework layers. Chemistry: A European Journal, 13(35): 9862-9865. https://doi.org/10.1002/chem.200701009

Yeong, Y.F. and Khoo, T.S., 2019. Fabrication of amino-functionalized CAU-1/cellulose acetate mixed matrix membranes for CO2/N2 separation. Key Engineering Materials, 797: 39-47. https://doi.org/10.4028/www.scientific.net/KEM.797.39

Yin, H., Wang, J., Xie, Yang, Z.J., Bai, J., Lu, J., Zhang, Y., Yin, D. and Lin, J.Y.S., 2014. A highly permeable and selective amino-functionalized MOF CAU-1 membrane for CO2-N2 separation. Chemical Communications, 50(28): 3699-3701. https://doi.org/10.1039/C4CC00068D

Yong, W.F. and Zhang, H., 2020. Recent advances in polymer blend membranes for gas separation and pervaporation. Progress in Materials Science, (12 July 2020): 100713. https://doi.org/10.1016/j.pmatsci.2020.100713

Zahri, K., Wong, K.C., Goh, P.S. and Ismail, A.F., 2016. Grapheneoxide/polysulfone hollow fiber mixed matrix membranes for gas separation. RSC Advances, 6(92): 89130-89139. https://doi.org/10.1039/C6RA16820E

Zhang, C., Dai, Y., Johnson, J.R., Karvan, O. and Koros, W.J., 2012. High performance ZIF-8/ 6FDA-DAM mixed matrix membrane for propylene/propane separation. Journal of Membrane Science, 389(February): 34-42. https://doi.org/10.1016/j.memsci.2011.10.003

Zhang, C.X., Wang, Z., Cai, Y., Yi, C.H., Yang, D.X. and Yuan, S.J., 2013. Investigation of gas permeation behavior in facilitated transport membranes: Relationship between gas permeance and partial pressure. Chemical Engineering Journal, 225(June): 744-751. https://doi.org/10.1016/j.cej.2013.03.100

Zhang, F., Dou, J. and Zhang, H., 2018. Mixed Membranes comprising carboxymethyl cellulose (as capping agent and gas barrier matrix) and nanoporous ZIF-L nanosheets for gas separation applications. Polymers, 10(12): 1340. https://doi.org/10.3390/polym10121340

Zhang, F., Ren, H., Shen, L., Tong, G. and Deng, Y., 2017. Micro-nano structural engineering of filter paper surface for high selective oil-water separation. Cellulose, 24(7): 2913-2924. https://doi.org/10.1007/s10570-017-1292-z

Zhang, H., Guo, R., Hou, J., Wei, Z. and Li, X., 2016a. Mixed-matrix membranes containing carbon nanotubes composite with hydrogel for efficient CO2 separation. ACS Applied Materials and Interfaces, 8(42): 29044−29051. https://doi.org/10.1021/acsami.6b09786

Zhang, M., Deng, L., Xiang, D., Cao, B., Hosseini, S.S. and Li, P., 2019. Approaches to suppress CO2-induced plasticization of polyimide membranes in gas separation applications. Processes., 7(1): 51. https://doi.org/10.3390/pr7010051

Zhang, Y., Balkus, K.J., Musselman, I.H. and Ferraris, J.P., 2008. Mixed-matrix membranes composed of Matrimid and mesoporous ZSM-5 nanoparticles. Journal of Membrane Science, 325(1): 28-39. https://doi.org/10.1016/j.memsci.2008.04.063

Zhang, Y., Feng, X., Yuan, S., Zhou, J. and Wang, B., 2016b. Challenges and recent advances in MOF-polymer composite membranes for gas separation. Inorganic Chemistry Frontiers, 3(7): 896-909. https://doi.org/10.1039/C6QI00042H

Zhao, D., Ren, J., Qiu, Y., Li, H., Hua, K., Li, X. and Deng, M., 2015. Effect of graphene oxide on the behavior of poly (amide-6-b-ethylene oxide)/graphene oxide mixed-matrix membranes in the permeation process. Journal of Applied Polymer Science, 132(41): 42624-42634. https://doi.org/10.1002/app.42624

Zhao, D., Ren, J., Wang, Y., Qiu, Y., Li, H., Hua, K., Li, X., Ji, J. and Deng, M., 2017. High CO2 separation performance of Pebax®/CNTs/GTA mixed matrix membranes. Journal of Membrane Science, 521: 104-113. https://doi.org/10.1016/j.memsci.2016.08.061

Zornoza, B., Gorgojo, P. Casado, C., Téllez, C. and Coronas, J., 2011. Mixed matrix membranes for gas separation with special nanoporous fillers. Desalinationa and Water Treatment, 27(1-3): 42-47. https://doi.org/10.5004/dwt.2011.2045

Zornoza, B., Irusta, S., Tellez, C. and Coronas, J., 2009. Mesoporous silica sphere-polysulfone mixed matrix membranes for gas separation. Langmuir, 25(10): 5903-5909. https://doi.org/10.1021/la900656z

Zulhairun, A.K., Fachrurrazi, Z.G., Izwanne, M.N. and Ismail, A.F., 2015. Asymmetric hollow fiber membrane coated with polydimethylsiloxane-metal organic framework hybrid layer for gas separation. Separation and Purification Technology, 146(May): 85-93. https://doi.org/10.1016/j.seppur.2015.03.033